High Air Compressor RC Hammer Reverse Circulation Drilling

High Air Compressor Used RC Hammer Reverse Circulation Drilling RC series reverse circulation DTH hammer is the latest developed product of our company. It is mainly used for deep exploration drilling and core sampling.Reverse Circulation RC DTH Drill BitRCseries reverse circulation DTH Hammer is the latest developed product of our company. It is mainly used for deep exploration drilling and ore grade control. It has the following characteristics:1.Based on previous experience of ordinary hammers, combined with the features of reverse circulation hammer, optimized internal structure and ideal energy transfer, thus ensuring the series of hammers drilling with fast, smooth and continuous sampling.2. The internal structure is very simple with components of high rigidity, thus ensuring long life and easy maintenance of the hammer.3.The collection tube adopts an integrative design and can be replaced without disassembling the hammer. With carburizing treatment, it has good abrasive resistance.4.Equipped with bits designed with patent. Simply by replacing the drill bit, the same hammer can drill holes of different sizes ensuring that the sample is not contaminated.5. In difficult conditions such as loose soil, hard rock and plenty of water exists, sampling can be done well.Reverse Circulation Hammers Specification:Reverse Circulation HammersDescriptionWeight(kg)RC45RC55RC65RC521. Internal Circlip0.030.040.050.042. Air Screen0.350.440.650.443. Top Sub6.509.6520.009.654. "O" Ring0.010.020.020.025. Sample Tube5.106.7212.506.756. Check Valve0.250.680.850.687. Spring0.040.120.100.128. "O" Ring0.010.020.020.029. Air Distributor0.851.483.501.4810. "O" Ring0.020.010.020.0111. Internal Cylinder2.204.124.204.1212. Piston8.5016.9024.0016.9013. External Cylinder14.5019.5032.0021.5014. Guided Sleeve1.200.905.501.9015. "O" Ring---0.0216. Stop "O" Ring---0.0117. Stop Ring---0.3218. Shrout---1.8619. Drive Chuck3.205.656.504.1720. Bit Retaining Pin0.010.150.30-21. Drill Bit10.5015.8031.0011.05Technical Data ModelRC45RC55RC65RC52Length (Without Bit)1020mm1111mm1250mm1208mmWeight (Without Bit)94.00kg66.50kg110.00kg70.00kgExternal Diameterφ99mmφ126mmφ146mmφ126mmBit ShankNRC45NRC55NRC65PR52Hole Rangeφ114 - φ127mmφ133- φ152mmφ155- φ190mmφ133- φ146mmConnection ThreadAs requiredAs requiredAs requiredAs requiredWorking Pressure1.0 - 3.0 Mpa1.5 - 3.5 Mpa1.5 - 3.5 Mpa1.5 - 3.5 MpaImpact Rate at 17 Bar30HZ35HZ28HZ35HZRecommended Rotation Speed25 - 40 r/min25 - 40 r/min25 - 40 r/min25 - 40 r/minAir Consumption1.0Mpa: 8 m³/ min1.7Mpa: 16 m³/ min1.7Mpa: 20 m³/ min1.7Mpa: 16 m³/ min1.8Mpa: 12 m³/ min2.4Mpa: 22 m³/ min2.0Mpa: 26 m³/ min2.4Mpa: 22 m³/ min2.4Mpa: 16 m³/ min3.0Mpa: 28 m³/ min3.0Mpa: 35 m³/ min3.0Mpa: 28 m³/ min Basics of Reverse Circulation Drilling:(1) RC drilling uses rods with inner and outer tubes, the drill cuttings are returned to surface inside the rods. The drilling mechanism is a pneumatic reciprocating piston known as a hammer driving a tungsten-steel drill bit.(2) RC drilling utilizes much larger rigs and machinery and depths of up to 500 meters are routinely achieved. RC drilling ideally produces dry rock chips, as large air compressors dry the rock out ahead of the advancing drill bit.(3) RC drilling is slower and costlier but achieves better penetration than RAB or air core drilling; it is cheaper than diamond coring and is thus preferred for most mineral exploration work.(4) Reverse circulation is achieved by blowing air down the annulus of the rod, the differential pressure creating air lift of the water and cuttings up the inner tube which is inside each rod. It reaches the deflector box at the top of the drill string then moves through a sample hose which is attached to the top of the cyclone.The drill cuttings travel around the inside of the cyclone until they fall through an opening at the bottom and are collected in a sample bag. For any drill hole there will be a large number of sample bags, each one marked to record the location and drilling depth that the sample was obtained.The collected series of sample bag cuttings are later taken for analysis to determine the mineral composition of the drill hole. The analysis results of each individual bag represents the mineral composition at a particular sample point in the drill hole. Geologists can then survey the drilled ground analysis and make decisions about the value of the overall mineral deposit.Applications1. Mine and quarry2. Road construction for the drilling and blasting work3. Water well drilling4. Slope protection   /* March 10, 2023 17:59:20 */!function(){function s(e,r){var a,o={};try{e&&e.split(",").forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1