1.Working Theory of Waste Treatment
EquipmentSpecificationNo.NameParameter1The Raw Materialsolid waste/
waste rubber/ waste plastics/ waste tyre2Total Capacity5t/day,
10t/day, 12t/day, 50t/day3The size of reactor2.6m*6.6m, 2.6m*7.7m,
2.6m*8.8m, customized4Average oil
productivitytyre:40%-50%,plastic:60%-70%5Average carbon
productivity30%-35%6Average steel productivity10%-15%7Average
waste-gas productivity5%8Pyrolysis time8h9Discharge time3h10Feeding
timme1hThe crushed domestic garbage or the pulverized small
rubber block (recommended not more than 5cm, the smaller the
better, preferably not including steel wire) or the plastic is
automatically transferred to the feeder of the main furnace, sealed
into the main furnace for catalytic cracking After gasification,
the oil gas subgas package enters the three condensers in sequence
to be condensed into liquid oil and is stored in the transfer tank.
The non-cooled gas is purified and then enters the collection and
recovery system and returns to the fuel chamber to serve as fuel
for production; while the carbon residue portion passes through The
slag discharger is separated from the furnace body and stored in
the carbon black storage tank under the action of negative pressure
collection for use. The entire process runs from feed to slagging,
and the oil is continuously discharged without any emissions.Gas
treatment in the production process: The gas produced in the
production process is about 3~10% of the total amount of oil, and
the heat is large, the pollution is strong, and it cannot be
directly discharged. We use a gas recovery device to purify all the
gases for dechlorination and then recycle them to the combustion
chamber for fuel use, which not only avoids pollution, but also
avoids waste of resources and greatly saves production costs. Of
course, if necessary, these gases can also be collected and
compressed for gas power generation or for sale in the market.This
process uses the principle of low temperature cracking. The normal
cracking temperature is 0 °C ~ 400 °C. During the whole production
process, the pressure is micro negative pressure. Moreover, the gas
purifier is also used in the new design, and the flue gas emitted
at the end is more clean and more environmentally friendly.2.Main
Parts1. Horizontal type revolving reactor 2.
Heavy oil tank3. Automatic carbon black discharge 4.
Gas separator5. Automatic carbon black discharge 6.
Controller7.Gas recycling system 8. Draft fan
9. Motors10.Slag cart 11. Cooling
tower 12. Oil pipe13.Oil
tank 14. Water Pool
15. Blower3. Basic Operation4.Our Advantages1.
The pyrolysis furnace body adopts the structure of heat storage
body, which fully recycles the waste heat. That can not only extend
the service life of the main furnace, but also save fuel, leading
to further savings in production costs.2. The furnace bladder
adopts specially high-temperature resistant quasi-brand boiler
steel, and the service life can reach 8 years.3. The equipment is
installed with self-developed infrared anti-blocking early warning
dredging device, which is the exclusive device developed by our
company. It can figure out pipeline blockage phenomenon in the
production process, sound an early warning and automatically solve
the problem to ensure that the main furnace will not have safety
problems due to pipeline blockage during the production process.4.
The slag discharge system adopts a double-cycle structure, which
controls the slag discharge time within about 40 minutes. The
system can discharge slag quickly and cleanly. 5.
Self-developed chemical accelerator of our company increases the
oil yield by 3%-8%.6. Adopting a new exhaust gas purification
system can make the gas emitted after purification meet the
relevant national emission standards.7. Excess combustible gas is
dehydrated and desulfurized by the purification system and then
stored in a gas storage tank after compression by a special gas
compressor, which can be used for heating later, and can also be
supplied to gas generators for use or sale.8. The main furnace uses
more convection vents and rapid cooling devices, so that its
temperature drops below 100 degrees within three hours.5.Our
Services 5.1 Pre-sales Service: The wide product
range enables us to provide our customers with machines or complete
processing plants.Based on our customers' request and budget, our
experts make efficient and reliable solutions.Following customers'
order we produce strictly. What's more, before placing the order
every customer has the chance to visit working machines or complete
plant in the site.5.2 After-sales Service:1.Quality warranty
period: One year warranty for the reactor ,and lifetime
maintenance for complete set of machines. pay the double air
tickets, accommodation and food.2.According to the requirement of
the buyer, our company sends engineers for installation and
commissioning in buyer's site including the training of skills of
buyer
Related products about Mini 1ton Waste Plastic Pyrolysis Plant to Get Fuel Oil
- Waste Tyre Plastic Recycling Machinery Machine Tire Crusher Production Line Rubber Crumb Grinding Machine Equipment Tire Shredder
- Stretch Plastic Blowing Pet Bottle Making Blow Molding Machine Bottles Stretch Automatic Pet Bottle Blowing Machine
- Waste Plastic Pet Bottle, Water Bottle Flake, PP/HDPE/LDPE PE Film Jumbo Woven Bags Plastic Crusher Machine, Plastic Crushing Washing Recycling Machine
- Type 2 Wall-Mounted Electric Car Charging Station 7kw /11 Kwelectric Vehicle Charging Station Home Wallbox AC EV Charger Single Phase or 3three Phase
- G-View G12W Wholesale Auto Car LED Headlight Bulb High Power H13 H11 9005 H7 H4 Car LED Headlights LED Car Lights
- New Design Porcelain Round Plates Dinner Set for Wedding and Banquet
- China 2023 New Design Super Soft 100% Polyester Microfiber Knitted Oversized Decoration Hoodie Blanket
- Handmade Art Creative Materials Thickened White Paper Cup DIY Disposable Handmade Colored Paper Cup