Rubber block cutter machine to cut tire into small pieces This
machine can cut the strips tire into 25mm- 50mm blocks. And then
the crusher machine can shredder them into
granulesParemeterItemSpecificationMotor power15kwSpeed of main
screw420 r/minOut diameter of
cutter200mmDimension1080x850x1250Purpose: To Cut the strip
into block 50mm or 25mm by adjusting blade number and belt
width Structural principle
:1. The device consists of frame, motor, transmission mechanism, balance equipment, two move knives and a fixed knife, and the compression gear etc. 2. Knife is made from alloy, hard wear resistant, can be used after repeatedly grinding.3. Uniform speed of the device, shear force, low energy consumption, easy operation and safety.Waste
Tyre Recycling Line1. Rubber Crumb Machine Tyre Circular
CutterTyre Circular CutterCut Tire Bead From The Whole TireModel:
HKR-1000Power: 3KwCapacity: 30-40 Tires/HourWeight: 300KgOverall
Dimensions: 1650×1050×1500mmOperation:Put tiPut tire on the round
platform, rotate the wheel to make the four claws catch inside of
tire and fix steady, start the cutter machine, the platform
rotates, handle the cutting knife control stick, the knife cut into
tire, adjust the cutting depth until the tire sidewall cut
off.Features:Reasonable design, stable performance, high quality,
ease operation, long service life, low noise, no pollution,an ideal
equipment for tire recycling.2.Rubber Crumb Machine Tyre
Strip Cutter Tyre Strip CutterCut The Whole Tire Into Strips
Except Tire BeadModel: HKS-1000Power: 5.5KwCapacity: 1
T/HourWeight: 700KgOverall Dimensions: 1300×800×1500mmAdjustment Of
Rubber Strip Width:There is a guiding rule in the middle of the two
blades and the rubber strip width is up to the distance between the
guiding rule and blade. The distance means the rubber strip width.
The guiding rule can be adjusted by the left and right movement of
the two screw rods.Rubber Crumb Machine Blade Maintenance:When the
blade is not sharp, sharpen the blades with angle grinder. When
sharpening the blades, the grinding wheel shall not focus on one
position for a long time. When changing the blades, remove the
lower blade first and then remove the upper blade; when installing
the blades, fix the upper blade first and then fix the lower
blade.Rubber Crumb Machine Maintenance:1, Check the motor if the
default phase happens or if the short circuit happens, and check if
the change -over switch works normally;2, Check the gearbox and big
gears if they are short of oil;3, The two blades are connected by
two main shafts and each main shaft is supported and fixed by two
sets ofbearings. Check the bearing if the lubricating oil is
short.3. Rubber Crumb Machine Tire Block Cutter Tire Block
CutterCut Tire Stirp Into 3--8cm BlocksModel: HKB-1000Power:
15KwCapacity: 1 T/HourWeight: 650KgOverall Dimensions:
1080×850×1250mmOperation:The rubber block cutter is used to cut
rubber strips into 3--5cm blocks for grinding into rubber powder or
rubber granule in the next step.Application:Start the power, put
tire strips into the feeder, and then strips will be cutted into
3-5cm rubber blocks4. Rubber Crumb Machine Steel Wire
Extruder Steel Wire ExtruderSeparate The Steel Wire From The
Tire BeadModel: HKW-1000Power: 18.5KwCapacity: 1 T/HourWeight:
1400KgOverall Dimensions: 1600×1420×1200mmOperation:Start the
power, put tire bead into the rollers of the steel wire extruder
and then start the button to make the tire bead enter the rollers.
After separating the rubber and steel wire, start the button to
make the tire bead get out of the rollers, and then take out the
tire bead from the rollers, so you get a complete steel wire
ring.Application:This steel wire extruder is mainly used to
separate the rubber and steel wire from the tire bead of all kinds
of tires and you can get a complete steel wire ring.Features:Easy
operation and maintenance, high separation efficiency. Rubber
Crumb Machine WORKING PROCESS1. Tire circular cutter cuts tire bead
from the whole tire;2. Tire strip cutter cuts whole tires into
strips except tire bead;3. Tire block cutter cuts tire strips into
3-8 rubber blocks;4. Steel wire extruder separates steel wire and
rubber out from tire bead. Packaging &
ShippingOUR CUSTOMERS FROM OVER 30 COUNTRIES AND REGIONSCUSTOMER
SITE Company ProfileQingdao Evertech Industry Co., Ltd. is
a professional pressure vessel designer, manufacturer and
exporter. We have manufacturing licenses for ASME U, ASME
U2,NB,PED, D1, D2 and A2 pressure vessels. Composed of more than 20
senior experts and professional engineers, the research and
development team, with more than 20 years of professional
experience, is committed to product design, development and program
optimization, and can provide high-quality solutions according to
users' requirements in different operating
conditions. Company has cover an area of 70000
manufacturing base and 15000 modern manufacturing plants, can
provide customers both at home and abroad wi
Related products about Waste Tyre Cutting Machine / Rubber Block Cutter / Rubber Tyre Cutter
- Waste Tyre Plastic Recycling Machinery Machine Tire Crusher Production Line Rubber Crumb Grinding Machine Equipment Tire Shredder
- Stretch Plastic Blowing Pet Bottle Making Blow Molding Machine Bottles Stretch Automatic Pet Bottle Blowing Machine
- Waste Plastic Pet Bottle, Water Bottle Flake, PP/HDPE/LDPE PE Film Jumbo Woven Bags Plastic Crusher Machine, Plastic Crushing Washing Recycling Machine
- Type 2 Wall-Mounted Electric Car Charging Station 7kw /11 Kwelectric Vehicle Charging Station Home Wallbox AC EV Charger Single Phase or 3three Phase
- G-View G12W Wholesale Auto Car LED Headlight Bulb High Power H13 H11 9005 H7 H4 Car LED Headlights LED Car Lights
- New Design Porcelain Round Plates Dinner Set for Wedding and Banquet
- China 2023 New Design Super Soft 100% Polyester Microfiber Knitted Oversized Decoration Hoodie Blanket
- Handmade Art Creative Materials Thickened White Paper Cup DIY Disposable Handmade Colored Paper Cup