High-Efficiency Turbine Super-Micro Classifier-Jcsf-V

 High-Efficiency Turbine Super-Micro Classifier      Our Main Products:                                      Working Principle:The balance between the centrifugal force generated by the rotating turbine and the centripetal force created by the air.The material to be graded is sucked into the grading chamber by the high-pressure negative pressure suction system through a feeder,and is subjected to strong and powerful centrifugal force field near the volute casing and the staged turbine. After satisfying the requirements,the fine powder is sucked out of the grading impeller and collected by the collecting device. Then drop the lower box, here due to the impact of the second into the air was dispersed again, the fine powder mixed with the coarse powder again with the air into the classification zone, the coarse material along the inner wall is col-lected by the off-fan. As the turbine and the uppertank body with air seal, making the sealing effect is very superior,more uniform particle size.By adjusting the speed of the drive motor and the amount of secondary air intake,the best grading effect can be obtained.Technical Parameter:  MODELProduct fineness d97=umProcessing capacity kg/hGrading wheelMotor power(KW)Speed (r/min)Diameter (mm)2508-100300-1000600-60002505.53158-120500-2500500-48003151140010-120800-5000400-38004001550012-1201250-8000300-30005002263012-1202800-19000250-240063030 80015-1504000-25000200-190080037Overview:JCSF-V high-efficiency turbine super-micro classifier is suitable for low to medium hardness material classifier of superfine classifying equipment that our company is based on digesting and absorbing foreign advanced powder technology. The performance indicators have reached the international similar model standard. The machine with secondary air inlet and high-precision turbine,which obtain the fine materials of up to 8 microns, and rotors with special materials can be classified high hardness materials,widely used in chemical,pharmaceutical,food, non-metallic mineral industries such as the classification of ultrafine powder particles, except iron, selected, etc. Performance feature:Technical Services:Technical handover includes engineering and design of a full set of process technology.We propose to provide the following services, including consulting services, installation guidance, commissioning, trial production guidance and training.Aftersales Service:Equipment warranty for 1 year (consumer parts: except for shredding discs and ring gears). The warranty period for bearings is as follows: one year of operation for 8 hours of service is warranted for one year; one day of operation for more than20 hours is warranted for 6 months.The cost to the buyer's factory within five days is included in the total price of the equipment and the customer provides an international round-trip ticket.For more than 5 days, the service fee will be charged at 145 USD per day per person.If the customer is all ready to install the mill, the equipment can be installed and debugged basically for three days.We are responsible for guiding the installation and commissioning.Responsibility of Buyer and Seller:Seller:We will provide installation and commissioning and engineering technical support. The scope of the provision will be defined in detail within the contract. Buyer:The supply of equipment and installations, technical data, and construction materials for local supply are provided by the buyer:- Power supply and cable- Parts that are not mentioned in the quotation or that are explained by the local supply.The following work and services are the buyer's responsibilities:- Equipment transportation costs- Equipment installation, commissioning, commissioning personnel, except for supplier personnel- Sufficient raw materials and storage equipment for commissioning- Transportation tools, cranes and lifting devices-The customer need to arranges 2~3 installers to install the equipment.Delivery and Payment Terms:1.priceFOB price, including shipping to Shanghai port, properly packaged, including tax.2.payment termAfter the contract is signed, a 30% deposit will be paid.And the remaining 70% of the payment is paid before shipment. Customers can come to the factory for acceptance and can run the finished mill with materials.3. delivery timeReceive orders, find out all technical and business details and receive approximately 30 working days after receiving the deposit.4.valid period60 days from the date of quotation    System  Process:   Technical Support:Upon receiving the deposit, we will offer the following technical services:1. Design for your production line flow and equipment layout, free of charge;2. Provide foundation drawings of customer-ordered grinding mills and drawings of related parts, etc;3. Technical parameters of peripheral equipment will be supplied;4. Free technical suggestions on adjusting of equipment layout and application.5. Equipment upgrading (customers need to pay the cost);Quality Assurance