Specifications of 900MHz Bandwidth Adjustable Digital Repeater
Model:BT-LS37E4-900 The Digital Repeater is designed to
provide a more cost-effective solution than adding a new Base
Transceiver Station (BTS) to improve signal coverage and
communication quality in single system. And its easy installation
and maintenance can help carrier get fast return.The repeater is
working as a relay between the BTS and mobiles. It receives the
low-power signal from BTS via the Donor Antenna, linearly amplifies
the signal and then retransmits it via the Coverage Antenna to the
weak/blind coverage area. And the mobile signal is also amplified
and retransmitted to the BTS via the opposite direction.
Features Aluminum-alloy casing with IP65
protection has high resistance to dust, water and corrodingSoftware
defined filter supporting up to 2 sub-bands adjustable in each
individual frequency bandLow interference to BTS by adopting linear
amplifier with high gain and low noiseAdopting filter with highly
selectivity and low insertion loss eliminates interference between
uplink and downlink ApplicationsTo expand signal coverage or
fill signal blind area where signal is weak or
unavailable.Outdoor:Airports, tourism regions, golf courses,
tunnels, factories, mining districts, villages, …Indoor:Hotels,
exhibition centers, basements, shopping malls, offices, parking
lots, …Applications Application Diagram
Technical
SpecificationsItemsSpecificationsSystemGSM/UMTS/LTEWorkingFrequency(Customized)Uplink890~915MHzDownlink935~960MHzBandwidth4
sub-bands, each 0.2~10MHz Tune BandwidthMaximum Gain85±3dBMaximum
Output Power Uplink30dBmDownlink37dBmALCSupportGain Adjustment
Range0-31dB in step of 1dBVoltage Standing Wave Ratio≤ 1.5Maximum
Input power(Non-destructive)0dBmError Vector Magnitude(EVM)≤ 8%Peak
Code Doman Error(PEDE)≤ -35dBSpurious Emission9KHz~1GHz ≤
-30dBm1GHz~12.75GHz ≤ -36dBmThird-order Inter-modulationComply with
3GPP TS 25.106 V6.0.0Noise Figure≤ 8dBSystem Delay≤ 8.0μSecI/O
Impedance50ΩRF ConnectorN-Type (Female)Temperature RangeOperation:
-25°C ~ + 55°CRelative Humidity Range≤ 95% (non condensing)Power
Supply
(customized)AC220V,50/60HzDimensions428*328*175mmWeight≤15kgNMS
Monitoring Function(Optional)Real-time alarm for door status,
temperature, power supply, VSWR, etc;Remote control such as turn
on/off, increasing/decreasing output power, etc;Real-time status
for output/input power, UL/DL gain, all status of repeater
etc. Installation & Commissioning1.1 Installation1.1.1
Steps for mounting on the Pole At Donor site, install the FSR
Donor Unit, Donor Antenna, Link Antenna, and RF cable as per
specified plan and site layout. FSR Donor Unit can be pole-mounted
using the brackets as shown below.Place M8 screws through the holes
of H type brackets as shown in figure 1Fix combiner onto the H type
brackets with M6 screwsFix H type brackets with combiner installed
onto the pole with U type brackets and M8 screws Figure
1 Repeater Mounting Bracket Orient the Link Antenna of Donor
Site to the direction of the Remote Site.Use Site Master to measure
the VSWR of the RF cable from the Link Antenna. The value should be
less than 1.5; Otherwise, check the connectors and the installation
of the cable.Start Commissioning the Donor Unit .Proceed to the
Remote Site.At Remote site, install the FSR Remote Unit, Link
Antenna, Coverage Antenna, and RF cables. Remote Unit can be wall
mounted or pole mounted depending on the approved plan.Orient the
Remote Link Antenna to the direction of the Donor Site.Using
Spectrum Analyzer, check the Link RSL; adjust the Link Antennas of
both Donor and Remote until the required RSL is achieved. Link RSL
can be computed using conventional path calculation method.Then,
measure the VSWR of the RF cables connecting with the Link Antenna
of Remote Unit. The value should be less than 1.5, otherwise, check
the connectors and the installation of the cable.Start
Commissioning the Remote Unit .1.1.2 Steps for mounting on the
wall At Donor site, install the FSR Donor Unit, Donor Antenna,
Link Antenna, and RF cable as per specified plan and site layout.
FSR Donor Unit can be wall-mounted using the brackets as shown
below.Make four marks on the wall according to the dimension shown
as figure 2Drill four holes at position markedFix two pcs H type
brackets on the wall with M8 expansion screwsFix combiner onto the
brackets with M6 screws Figure 2 Repeater Mounting
Bracket 6. The following steps are the same with
step 4 to 12 for mounting on the Pole. 1.2
CommissioningConnect the RF cable from Donor Antenna to the
spectrum analyzer and check if the Donor Antenna is receiving the
correct frequency; and then measure the signal level of the said
frequency (RSL). Adjust the antenna to make the readings approach
the recorded value on the survey report. Record all readings.Inside
the repeater, disconnect the uplink duplexer to the ICS module so
as to cut any signal coming from air going to the uplink duplexer
an
Related products about GSM WCDMA Lte 900MHz Bandwidth Adjustable Digital Amplifier
- Waste Tyre Plastic Recycling Machinery Machine Tire Crusher Production Line Rubber Crumb Grinding Machine Equipment Tire Shredder
- Stretch Plastic Blowing Pet Bottle Making Blow Molding Machine Bottles Stretch Automatic Pet Bottle Blowing Machine
- Waste Plastic Pet Bottle, Water Bottle Flake, PP/HDPE/LDPE PE Film Jumbo Woven Bags Plastic Crusher Machine, Plastic Crushing Washing Recycling Machine
- Type 2 Wall-Mounted Electric Car Charging Station 7kw /11 Kwelectric Vehicle Charging Station Home Wallbox AC EV Charger Single Phase or 3three Phase
- G-View G12W Wholesale Auto Car LED Headlight Bulb High Power H13 H11 9005 H7 H4 Car LED Headlights LED Car Lights
- New Design Porcelain Round Plates Dinner Set for Wedding and Banquet
- China 2023 New Design Super Soft 100% Polyester Microfiber Knitted Oversized Decoration Hoodie Blanket
- Handmade Art Creative Materials Thickened White Paper Cup DIY Disposable Handmade Colored Paper Cup