1000/2000 Watt Digital Ultrasonic Generator 28kHz/40kHz for Vibration Transducer

1000/2000 Watt Digital Ultrasonic Generator 28khz/40khz For Vibration TransducerUltrasonic Generator Details I. Summary of Performance: With more than 10 years research and application experience, we explored this microprocessor controlled, newly designed generator specially for ultrasonic cleaning.  The control box adopts advanced techniques, like separate-excited circuit, controlled by microcomputer, frequency automatic tracking and frequency sweeping, etc. Compared with traditional control box, it has better performances of stable and reliable operation and constantly adjustable ultrasonic frequency, which can develop the potential capacity of transducer in maximum. The automatic tracking of operating frequency can optimize output matching, strengthen power and raise efficiency. With the unique frequency-sweeping operating pattern, the cleaning solution can form a fine stream of refluence, which can time wash off the dirty uncovered by ultrasonic wave from the surface of working pieces and thus reach faster and thorough cleaning effect and raise the efficiency of ultrasonic cleaning. At the same time, it has perfect protective capacity: over temperature protection and overcurrent protection for more reliable operation; 4-bit timer for more accurate time control to second. With digital power adjustment, it can meet different cleaning demands. It permits optional alteration at working state, so the operation is freer. The complete appliance adopts building block design. With computer fault location and display system, its operation and maintenance are more convenient. Protected by rust proof and isolated structure, this generator can work under rigid circumstances. II. Key Technical Indexes Working volt: 220V 10% Working current:  Attention:the appliance can not stay above maximal current long time.   rating power300W600W900W1200W1500W1800W2400W-2500W3000Wmaximal current1A2.5A3.5A4.5A5.5A6.5A8.5A10AEnvironment temperature: 0-40C° Relative humidity: 40%--90% Working frequency: 28KHz(40KHz,80 KHz,135KHz, etc)5% Time control: 0-59 minutes 59 seconds Range of power control: 0-100%   digital control and adjustment of 16 grades Internal overtemperature protection: 65 C° Outer size:  L x W x H = 300 x 360 x 150 III. Instruction for panel Performance Display window: for displaying fixed time, power, working state and faults. Switch for frequency sweep: selecting normal or frequency-sweeping working state.On/Off: controlling operation and pause of working state.Adding fixed time: set value of working time.Reducing fixed time: set value of working time.Raising power: raising output power.Reducing power: reducing output power. Remark: Display board setting Before Power On machine, keeping press "Sweep"button ,and then the same time power on,so that the machine is into a setting status,via power +/- to change the display window of item number,and via Timer +/- to change the content of display window Item number 001, for when machine power on,the ultrasonic if start work.via Timer +/- would be change the display content, for "0"it standard for power on,but no ultrasonic, for "1"meaning power on,ultrasonic working normal Item Number 002, for displaying the working frequency or letter, via Timer +/-, when for "0" ,after power On,the machine will be display the frequency, for "1" will be for letter after power On Item Number 003, for displaying the working actual frequency or setting frequency, via Timer +/-, when for "0" ,after power On,the machine will be display working actual frequency , for "1" will be for setting frequency which you fixed Item Number 004, for displaying the working actual  current or actual power, via Timer +/-, when for "0" ,after power On,the machine will be display working actual  current  , for "1" will be for actual power Item Number 005, for displaying the working actual  current or actual power or displaying setting current and power, via Timer +/-, when for "0" ,after power On,the machine will be display working actual  current and actual power , for "1" will be for setting well that current and power Item C010; setting the max. Working current,via Timer+/- to change the display content Item C011; setting the max. Display power Item C011;Setting the fixed frequency value   Upper windowBelow windowReamark 00000001 C001When Power on will be closeWhen Power on will be open C002Display frequencyDisplay letter C003Display actual frequencyDisplay setting frequency C004Display currentDisplay power C005Display actual current and powerDisplay setting current and power C010Setting the max.working current C011Setting the max. Display power C012Setting the fixed frequency value 8.Back of display board with 8 settings on POTENSION (7,8 for back up ): On the back of display board,Potension meter DIP was for 8 switches,please according to working requirement to set,among of them, Number 4 switch was setting well before come out of plant, Don't change it any more.   Switch Number123 456OFFNormal working sit