Multi-Casing Steam Turbine Stacked Multi-Cylinder Steam Turbine

Product DetailsProduct NameMulti-casing Steam Turbine Stacked multi-cylinder Steam TurbineType of outputDC/AC Three Phase/AC Single PhaseGenerator typeDC Generator/ Synchronous GeneratorPower100KW-2000KWA complete set of steam turbine island comprises of following equipments and sub-systems:  1.Turbine-generator set  ---power is generated through the action of generator driven by the turbine connected to it. 2.Water-condensation system--steam is condensed to water to be circulated to boiler and heated again. 3.Vacuum system     A.sub-system of main steam (where steam circulates to propel the blades of turbine )    B.water cycle system (where water circulates from condenser to be heated again )    C.DCS system (monitors the operation of turbine and adjusts output rate )    D. deaerating &water supplying system (where oxygen is removed to ensure good operation environment and water is supplied )4. Cooling Air system (for air-cooled unit only) 5. Generator system ( electricity is generated in this system) Our protocol of delivering power plant construction project is as follow:  1.The Argumentation of Project 2. Engineering Design     a. Turbo-Gen Set and its auxiliary systems     b.Layout of Condensed Water System     c.Layout of Heat System     d.Civil Construction and Structure of Turbo-Gen Set 3.Equipment Purchase     a.Turbo Generator Set and its auxiliary systems     b.Condensed Water System     c.Vacuum System     d.Lower Temperature Heating System 4. Civil Construction     a.Foundation and the upper structure of the Turbo Generator House     b.Foundation of Turbo-Gen Set and its auxiliary systems     c.Foundation of other structures 5. Operation & Maintenance     a.Operation of power plant (technical counseling)     b.Regular maintenance and inspection     c.Technical Training Program for power plant personnel     d.General Overhaul 6. Installation & Testing     a.Installation & testing for all systems & equipment provided     b.Installation, testing & trail run of all systems of a power plant (Optional)     c.Installation, testing & trail run of entire power plant (Optional) 7. Supply of Spare Parts Reference List No.ItemProject detail01CommissionerLafargeHolcimCentury Paper MillPolatSPGCL02LocationGombe State, NigeriaLahore, PakistanTurkeyIndia03Scope of serviceEPC projectEngineering, Purchase, Supervision of constructionEPC projectEPC project04Applicationservice power plantof a cement factoryservice power station of a paper millindependent power plantindependent power plant05Modelair-cooled condensing turbine islandcondensing/extracting turbinecondensing turbinereheat turbine06BrandSimonsHTPHTPHTC07Standard of engineeringDIN.GBGBGB08Layoutsingle-story layout with horizontal steam dischargedownward steam dischargedownward steam dischargedownward steam discharge09Technical parameterspresure of steam inlet:8.5MPtem. of steam inlet: 435C.rated power:16.5MWback pressure:15KPapresure of steam inlet:4.9MPtem. of steam inlet: 475C.rated power:18MWpressure of extraction:1.1MPflow of extracted steam:54.6Mpaback pressure:15KPapresure of steam inlet:8.83MPtem. of steam inlet: 435C.rated power:51MWback pressure:4.9KPapresure of steam inlet:16.7MPtem. of steam inlet: 538C.rated power:300MWpressure of extraction:1.1MPback pressure:10KPa10Performance (under standard condition)heat rate:2467kcal/kwsteam rate:4.16kg/kwheat rate:2206.5kcal/kwheat rate:2215.3kcal/kwsteam rate:4.16kg/kwsteam rate:3.64kg/kw  Product Description: DC motor is a rotating motor that can convert DC electric energy into mechanical energy (DC motor) or mechanical energy into DC electric energy (DC generator). It is a motor that can convert DC and mechanical energy into one another. When it runs as a motor, it is a direct current motor, which converts electrical energy into mechanical energy; when it runs as a generator, it is a direct current generator, which converts mechanical energy into electrical energy.      Induction furnace is used for smelting or insulating ferrous metals, non-ferrous metals, sponge iron, such as scrap iron, scrap steel, copper, aluminum and so on. Complete working equipment such as continuous casting machine, rolling mill, mainly used for the production of billet, steel bar, angle steel, H-beam, I-beam, etc. Using KGPS, IGBT, single or double power supply technology, PLC (Siemens) can be realized throughout the monitoring.        Main supply list: 2 sets of electric furnace body, 2 sets of hydraulic or mechanical tilting electric furnace mechanism, 1 set of control platform, 1 set of intermediate frequency control cabinet (6 pulse 1, 12 pulse 2, 24 pulse 4), low voltage control cabinet (6 pulse 1, 12 pulse 2, 24 pulse 4), 1 set of capacitor cabinet, 4 or 8 water-cooled cables; 1 water temperature alarm, 1 leakage alarm; 1 crucible mold, 1 liquid One batch of pressure steel pipe, one set of copper row, three water tanks. Transformer, cooling tower, furnace builder, furnace lining ejector, furnace cover.KGSP Induction E