Cheapest Microwave Dryer Within Vacuum

                                Cheapest Microwave Dryer Within Vacuum1.Machine Introduction:Design Structure1.All parts of equipment are made of high quality microwave electric components:   1) It uses 16 pieces of magnetrons which is original Korea Samsung or Toshiba (rated power 1000 w), high efficiency, strong ability to resist load, long life , use Taiwan built fan DP200A air-cooled heat protection device.   2) It adopts special transformer WBL-1000A with overheating protection (high voltage 100      kv transformer, high quality transformer for full copper core 8.0 kg of a real transformer industry, and design for double air-cooled heat protection).   3) The specifications of ultra-high voltage capacitor is (1.05 uf 2500 v) and more stable anddurable than the conventional (1.0 uf 2300 v) performance.   4) (CL04-12) high-voltage silicon stack (its chip is made in Japan), the reverse repetitive peak voltage can reach 12kv, positive commutation current is 450mA, and checked by practice, durable, entirely suitable for microwave equipment.2. Equipment adopts the cylindrical heating cavity body, which is made of 8 mm 304 # stainless steel plate,ensure to bear pressure, can be uses for a long time without deformation, conform to the requirements of GMP of pharmaceutical industry and QS of food industry.The phase complementary form microwave energy supply with elaborate design, ensure the normal operation of magnetron completely, with superior output matching performance, prolong service life.3.According to the drying characteristic of this material,It adopts complementary feed way distribution on power density distribution of the microwave heater, carefully designed each layer 2 complementary feed mouth scanning waveguide type, only after a large number of theory and practice can design the microwave waveguide to ensure the normal operation of magnetron completely, the output matching performance is superior, the uniform heated material more thoroughly and longer the service life of the microwave tube and transformer core, such as the original.   4.The machine adopts multi-open feed of heating body side, well-designed phase form complementary feed mouth (microwave power density designed according to the feeding situation), microwave waveguide is designed after a large number of theory and practices, so as to ensure the normal and complete operation of magnetron,with superior output matching performance, the materials heated more evenly and thoroughly,extend the service life of the core components such as microwave tube and transformer etc.   5. Outside frame and plate etc. are all made of stainless steel material,look nice.   6.On side of heating chamber open door large,with choke device, to ensure microwave equipment don't leak after long-term use,ensure use safety,convenient for production operation.   7.Chamber adopts horizontal rotating tray technology (make material dry quickly and even), a total of 8 layers, each layer height of about 120 mm, wheel diameter is about 750mm.   8.The humidity-discharging device of vacuum pump and chamber is connect at the bottom and upper part of vacuum chamber, with multiple vacuum water outlets.   9. There are cooling devices set at the microwave generator and power supply,to ensure every electrical components without damaging and aging after long-term work.The Control System   1. The machine is equipped with total control panel. It looks beautiful and simple.It can display the temperature of the materials in the chamber and the condition of the components.Through this total control panel,you can adjust the power of the machine,control the drying time,ect.   2. There is one unit of infrared temperature measurement system(LT-05) at the top of equipment chamber,they are made by Raytek Inc in America. It can control the temperature of the materials(temperature range:0-500 degree), the heat preservation temperature can be adjusted freely.You can adjust the drying temperature ,drying time and interval time,to realize continuous and discontinuous drying.Major Dispositions1) The heating cavity are made of 8 mm 304 # stainless steel plate.2) Outside frame and plates are all made of stainless steel material.3) Can feed mouths are sealed by PTFE which is specially made4)One set of the common button switch control system5) 16 pieces of magnetrons, which are original Korea Samsung [model OM75P - 11] (rated power 1050 w)6) 16 pieces of industrial transformer (DY36-1000w).7) One set of infrared radiation thermometer produced by (LT -05) company8) 16 pieces of high voltage silicon rectifier stack (CL04-12).9) 16 pieces of axial flow fan (DP200A) for heat protection.10)One set time control system11)One set water ring vacuum pump,power is 3KW.12)One set conversion motor (rotating speed is 5-8r/min)13)One set of the special transformer, magnetron2.Technical parameters:Model HT-WZ20 Voltage415V±8% Microwave Output Power16KWInput Power20kwMicrowave Working Frequency2450MHZ±50HZ Overall Dime