High Pressure Double Action Pneumatic Gas Booster Pump for Pressure Testing

Product detailsProduct DescriptionProduct Description The Terek gas booster equipment uses pure compressed air as the driving power source, and USES gas booster pump as the pressure source, Hydroge ,nitrogen, oxygen, helium,N2O,Argon, CO2 and other gases as the pressurized medium. The output pressure is proportional to the driving gas pressure.By adjusting the pressure of the driving gas source, the corresponding pressure of the pressurized gas can be obtained.When the pressure of the driving gas source is balanced with that of the pressurized gas, the pneumatic booster pump will be automatically stops and the output gas pressure is stabilized at the preset pressure. Therefore, it has the features of explosion-proof, energy saving, environmental protection, adjustable output pressure, small volume, light weight, simple operation, reliable performance and wide application range.To operate this system, The drive gas from the air compressor is required to start the Terek booster pump. The pressure of the drive gas can be adjusted by valves and pressure gauges, and the output gas pressure can be adjusted .The expected working pressure can be achieved by adjusting the pressure of the drive inlet.. When the driving air pressure and the output pressure are balance, the pump stops filling pressure and the output pressure remains at the preset value.TEREK gas booster pump uses compressed air to drive large area end piston to small area end to get high pressure gas output.. Can be used for compressed air and other gas, the output pressure can be adjusted by inlet valve,  The output can ensure gas is not contaminated. Automatic pressure maintaining. Driven by gas, No spark or Flame and No generating heat, Can use it in dangerous places. Product ParametersProduct parametersBasically the principle of operation is similar to a reciprocating amplifier where control of the piston at the end position is reciprocating , The automatic reciprocating motion of the piston is controlled by a built-in four-way valve.TEREK pumps are air driven at a drive air pressure of 3 to 8 bar (29 to 116 psi) by the normal air compressor. Refer to model technical parameters.Refer to model technical parameters.  Product namePneumatic Air driven gas booster pump Pressurized transfer and filling equipment.ModelGU-GTC-40Pressure ratio40:1Drive air source pressure3-8 bar.Maximum outlet pressure320 bar  (46400 psi)When the driven air pressure is 5.0 barHigh pressure outlet pressure is 200bar.When the driven air pressure is 6.0 barHigh pressure outlet pressure is 240bar.Min gas inlet pressure15 barMax gas inlet pressure320 barOutlet pressure Control unitDrive air regulator valvePressure control accuracyless than 1%F.S;Pressure measurement accuracy0.4 pressure gaugeValves and pipingHigh pressure needle valve and stainless steel pipingEquipment Weight52 KGExport wooden case total Weight62 KGEquipment Dimension700*500*650 mmPacking size:770*560*680  mmPacking SpecificationsStandard export wooden caseConnection size(inch) Gas inletNPT 1/4  Internal ThreadConnection size(inch)   Gas OutletNPT 1/4  Internal ThreadProduction time12-15 days.System configuration:GU-GTC series gas booster unit control cabinet mainly includes one sets of GTC series air-driven gas booster pump, pressure gauges, air filter, gas inlet filter, control valves, air regulating valve, pipelines, cabinet, and pressure release valve etc.The diameter of the drive cylinder:160mmDrive cylinder stroke:100mm        High pressure Cylinder stroke:100mmThe maximum driving pressure of the drive air is 8 bar/116psiDetailed ImagesDetailed Photos Product advantages 1. All pipes and fittings are made of stainless steel to ensure a long life2. The pump will stop working automatically when the output pressure reaches the preset value,3. Maintain long working hours with no energy expenditure4.No dissipated heat during the pressure holding phase5.No risk for explosion and spark in oil and gas field6. The pump will start automatically when the outlet pressure drops slightly or the air drive pressure increases.7. The working pressure can be adjusted by adjusting the pressure of the driven air. 8.Easy to install, move, use and maintain Application FieldsApplication : Gas transfer and filling(Argon/Helium/Hydrogen/Oxygen/Nitrogen/CO2/NO2/CH4/LNG/LPG/CNG/FM200 etc.)Charging of gas cylinder and accumulator with nitrogen and High pressure gas injection system for various industries1. Reliable, easy to maintain, compact and robust2. No heat, flame or spark risk     3. Infinitely variable cycling speed and output4. Pneumatic driven units do not require electrical connections       5. Easy to apply automatic controls6. No limit or adverse affect to continuous stop/start applications7. Seal systems designed for long working life 8. No air line lubricator required9. Hydrocarbon free - separation between air and gas sections10. Built-in cooling (most models)             11. Suitable for most gases12. Ability to stall