Xusheng Compass Stainless Steel Sanitary CIP External Cleaning Four Ways Mix-Proof Mixproof Valves

Xusheng Compass Stainless Steel Sanitary CIP External Cleaning Four Ways Mix-Proof Mixproof ValvesProduct DescriptionAppilicationThis design is designed to ensure product mixing and leak detection when two different products flow through the same valve, and can replace the use of a dual seat anti mixing valve . It is widely used in beer, beverage, dairy, food, fruit juice, pharmacy, biological, toothpaste, cosmetics and so onOperational PrincipleThis valve is normally in a normally closed (NC) state and is equipped with two small pneumatic valves. Normally, it is in a normally open (NO) state and only needs to supply compressed air to the pneumatic head to synchronously close the two small valves. The main valve core is equipped with two independent seals, forming a leak detection and cleaning chamber between the two seals. Leaking products can flow out from the small valve outlets on both sides and the seals can be replaced in a timely manner. When performing CIP cleaning, the fluid flow direction is facing the square core of the valve core, which can comprehensively clean the main valve core (with a taper on the main valve core) and make the external CIP valve insensitive to water hammer effect. It can replace the double seat anti mixing valve as a valve array.Product Parameters  StandardSMS,DIN,3AMaterial Contact PartsSS304/SS316L(1.4301/1.4404) Provided with material inspection report Material Non-contact PartsSS304(1.4301)Size1.5"-4", DN40-DN100   Integrated Body CombinationT11 00°,T11 90°,T11 180°,T11 270°T12 00°,T12 90°T21 00°,T21 90°T22 00°,T22 90°Assemble Body CombinatioT11, T12, T21, T22ConnectionButt-weld, Tri clamp, Male Thread, Female-Male Threaded, Union, Weld-Thread, FlangeSeal MaterialSilicone, EPDM, FKM, Buna. All seals material comply with FDA21CFR117.2600Power OptionPosition Sensor, C-top Controller, C-top Controller (AS-I)Proximity Switch6-36V DC, 2pc of NPN or PNP (Options)Input Power Supply24V DCMax. Working Pressure≤6bar(87si)Supply Pressure for Air Actuator4~8bar(58psi~116psi)Compressed Air ConnectionFurnish Air Pipe with Air Connector G1/8"Working Temperature Range-10~120 ºC (14 ~ 248ºF)External Surface TreatmentRa32~64uin(0.8~1.6um)Internal Surface TreatmentRa16~32uin(0.4~0.8um)CertificateISO 9001, FDA, SGS, CESupportOEM & ODM are welcomeApplicationBeer, Beverage, Dairy, Food, Fruit Juice, Pharmacy, Biological, Toothpaste, Cosmetics and so onQuality requirement for compressed air used in actuatorCompressed air connection: Furnish air pipe with air connector R1/8" Maximum particle size: 0.01mm Maximum oil content: 0.08ppm Dew point: 10ºC or lower below atmospheric temparture Maximum water content: 7.5g/kg  OptionsTechnical SpecificationsThe advantages Compared with Traditional Design1.Various standards can be provided: SMS,DIN 2.Material contacts parts: SS304 and SS316L3.Available in sizes from 1.5" to 4", DN40 to DN100 4.The gasket can be Silicone,EPDM,FKM,Buna.All seals material comply with FDA21CFR117.26005.Connection can be butt-weld, tri clamp, male thread, female-male threaded,weld-thread, flange or others upon request.6.Power operated: Position Sensor, C-top Controller, C-top Controller (AS-I) 7.The valve body can be customized with a wide selection of different connections. Max. Working Pressure≤6bar(87si) Supply Pressure for Air Actuator: 4~8(58psi~116psi) Temperature range: Domestic Silicone:-22 ~ 302°F (-30~150ºC) Domestic EPDM:14 ~ 230°F (-10~110ºC) Importing Silicone:-40 ~ 392°F (-40~200ºC) Importing EPDM:-13~ 266°F (-25~130ºC) Buna:5~ 212°F (-15~100ºC) FKM:14 ~ 392°F  (-10ºC~200ºC )1.Less components 2.Less space3.Easier maintenance 4.No dead corner 5.No contact between drain systerm and products 6.The separation chamber cleaning will do not occur any hydraulic - pressure and not influenced by the  equipment or valve status.  Packaging & ShippingTo better ensure the safety of your goods, professional, environmentally friendly, convenient and efficient packaging services will be provided.If small order and choose by express , the items are packed by shrink wrap and secondly carton cases. If heavy weight of cargo ,which be packed by strongly seaworthy ply-wooden cases . In order to protective items , which will be packed by safety and resistance to shock in ply-wooden casesContact UsIf you have any inquiry or question for our valves, please kindly do not hesitate to let us know soon.We also produce other valves and pumps, welcome to Xusheng here, we will try our best to quote you in competitive prices. Company ProfileXUSHENG & COMPASS are manufacturer and supplied with sanitary valves, pumps, pipe fittings, tanks, tube. They are widely used for food, beer, beverage, chemical,biological, pharmacy and so on. Totally 112nos of workers and the factory Covers 4035m2,our warehouse covers 1000m2. We have 29 sets of LG Mazak machines and other CNC machine from Japan ; Meanwhile,we have 2 sets of automatic machining unit. Here is our range of products as below. A. Sanitary valve i