Hydrogen Fuel Cell Pem off Grid H2 Backup Power Hydrogen Electricity Generator 5kw 20kw 50kw 100kw

PEM Hydrogen Fuel Cell SystemProduct DescriptionWith the continuous development of economy and society, the requirements for energy cleanliness and high efficiency are becoming more and more prominent.The energy structure is urgent. Hydrogen has been widely used for a long time due to its wide source, high calorific value and zero pollution.It is considered to be one of the clean energy sources with the most development potential, and hydrogen energy has also become an important way to adjust the energy structure.Among them, hydrogen fuel cell stack is an important application field of hydrogen energy.In terms of hydrogen requirements for hydrogen fuel cell stacks, it is in line with the hydrogen standard GB/T of general industrial industries.3634.2-2011 is very different. As shown in the figure below, GB/T 37244-2018 "Proton Exchange Membrane Fuel Cell GasVehicle Fuel Hydrogen", in terms of hydrogen purity, 99.99% of high-purity hydrogen can meet the requirements of 99.97% of fuel hydrogen.It should be noted that CO≤0.2ppm is required.Product ParametersGB/T37244-2018 "Hydrogen Fuel for Proton Exchange Membrane Fuel Cell Vehicles"Project nameIndexHydrogen purity (molar fraction)99.97%Total non-hydrogen gas300μmol/molMaximum concentration of single type impurities Water (H2O)5μmol/molTotal hydrocarbons (as methane) *2μmol/molOxygen (O2)5μmol/molHelium (He)300μmol/molTotal Nitrogen (N2) and Argon (Ar)100μmol/molCarbon Dioxide (CO2)2μmol/molCarbon Monoxide (CO)0.2μmol/molTotal Sulfur (as H2S)0.004μmol/molFormaldehyde (HCHO)0.01μmol/molFormic acid (HCOOH)0.2μmol/molAmmonia (NH3)0.1μmol/molTotal halogen compounds (as halide ions)0.05μmol/molMaximum particle concentration1mg/kg* When the methane concentration exceeds 2 μmol/mol, the total concentration of methane, argon and nitrogen is not allowed to exceed 100 μmol/mol.The fuel cell power station adopts PEMFC fuel cell technology, which directly converts hydrogen into electrical energy through chemical reaction and simultaneously generates a certain amount of heat energy, which gets rid of the limitation of Carnot cycle of traditional combustion reaction, and has the advantages of high power generation efficiency, small size, quietness and zero carbon emission. , full operating conditions and other advantages.The main advantages of fuel cell technology are as follows:(1) High power generation efficiency:Fuel cell power generation is not limited by the Carnot cycle. Theoretically, its power generation efficiency can reach 85% ~ 90%, but due to the limitations of various polarizations during operation, the current power conversion efficiency of fuel cells is about 40% ~ 60%. If the combined heat and power supply is realized, the total utilization rate of fuel can be as high as 90% or more.(2) Small environmental pollution:Because the fuel gas of the fuel cell must be desulfurized before the reaction, and electricity is generated according to the electrochemical principle, there is no high-temperature combustion process, so almost no nitrogen and sulfur oxides are emitted, which reduces the pollution to the atmosphere.(3) Less radiationThe fuel cell has a simple structure, less radiation and less loss. Even in the vicinity of a fuel cell power plant of the 11MW class, the measured radiation is very small.(4) High reliabilityWhen the load of the fuel cell changes, it will respond quickly (10%-100% load change within 15s). Regardless of overload operation above rated power or operation below rated power, it can withstand with little change in efficiency. Due to the highly reliable operation of fuel cells, they can be used as various emergency power sources and uninterruptible power sources.(5) Easy to constructThe fuel cell has an assembled structure, which is convenient for installation and maintenance, and does not require many auxiliary facilities. The design and manufacture of fuel cell power plants are quite convenient.Workshop EnvironmentCustomer Case Packaging & ShippingCompany ProfileSINOPED is a professional manufacturer and supplier machinery and equipment in China,We belong to SINOPED International Group.   We have a well-experienced team to manufacture machinery and equipments and a professional design institute.Due to our good credit and service,we have made great achievements in the past years. We have established long-term business relations with many customers and some of our overseas customers have appointed us to be their purchase agency in China.   In SINOPED you can get your desired goods with the best prices and good quality. Welcome your inquiries from all over the world.Why Choose UsFAQQ1. Are you really a manufacturer? Where is your factory? How can I visit your factory?Yes, we are a source manufacturer with headquarter located in Liaoning province China. Sinoped dates from 1947. We are Warmly Welcome You to Visit Our Factory if You Have a Travel Plan.   Q2. Why choose your company?With more than 70 years of precipitation, Sinoped has experien