Product DescriptionPVC series pressurized UF membrane modules use
imported PVC raw material with long service life,filtering
precision is 0.01 micron. Due to its high rigidity, PVC can be made
to thicker hollow fibers and bearhigh working pressure, which is
applicable to inside-out working mode. it has good water
permeability, mechanical properties, chemical resistance and
anti-pollution ability, and the cut molecular weight is 100,000
Dalton.Inside-out structure is applicable forraw water with low
turbidity and SS. When inside-out membrane modules work,
contaminants are rejectedinside hollow fibers without dead angles,
which are easy to be washed out.IGFUFC250 membrane module is
installed with hollow membrane filament with inner diameter of 1mm
and outer diameter of 1.8mm, and the filtration method is internal
pressure type, i.e. the raw water enters into the inner part of the
hollow filament first, and then is driven by the pressure
difference, and then permeates through the filament along the
radial direction from the inner to the outer part, which can filter
out all kinds of bacteria, colloids, suspended matter,
microorganisms and other harmful substances in raw water.It can
filter out all kinds of bacteria, colloid, suspended solids and
microorganisms and other harmful substances in the raw
water. Product Parameters IGFUFC250 technical
detailsModel IGFUFC250StructureInternal pressure typeMembrane
materialModified PVCCut molecular weight100000 DaltonNominal
membrane area48m2Filament diameter ID1.0mm,OD 1.8mm Out
sizeφ250mm×1710mmConnection sizeDN50 coupling; Pure water
flux12000L/H(0.15MPa, 25ºC) Product Features★ High filtering
precision: can reach 0.01μm★ High pure water flux:
35-100L/m.h★ High porosity: >95%★ High
strength:>600CN★ Long service life: 3~5 years service life
under normal use★ Low breaking rate of hollow fibers: to
ensures stable qualityof
ultrafitrate Application★ Treatment of surface water &
ground water ★ Municipal drinking water
treatment ★ Reuse of industrial wastewater ★ RO
pretreatment Detailed Photos Plant
photo Packaging & ShippingCustomer site Certification and
test report FAQ---Replace the filter cartridge step1. Receive
the production instruction to replace the cartridge and confirm
that the system has stopped running.2. Prepare the appropriate
filter element (specification, material, size, O-ring material,
type, etc.), disassembly tools, collection bucket, rags, etc.;
and3. Thoroughly clean the filter housing, empty around the filter,
and leave the operation area. Take protective gears with you.4.
Disconnect the filter to be replaced from the system. Slowly open
the exhaust port at the top of the filter and depressurise it,
paying attention to safety in the process to prevent material or
liquid from splashing.5. Empty the material in the filter, open the
filter cover with a tool, take out the filter cartridge, and pack
the cartridge in a plastic bag to be scrapped; 6 Use clean tools
and rags to clean the filter.6. Use clean tools and rags to clean
the inside of the filter and install the new cartridge.7. Open the
plastic bag at the open end of the filter element and check whether
the O-ring is intact and in place.8. Install the inflow of
materials according to the method of inflow from the outside of the
filter element and outflow from the inside of the filter element.9.
with the appropriate wetting agent (such as water) wet O-ring and
cartridge seat jack, hand-hold the cartridge near the end of the
O-ring, vertically insert the cartridge cartridge socket completely
into the cartridge seat jack, the cartridge inserted, remove the
cartridge bag, and then install the metal cover, with tools to
tighten the filter; 10 close the filter drain port, open the
plastic bag, open the filter, the filter is complete, in place.10.
Close the liquid discharge port of the filter, open the bleeder
valve at the top of the housing, slightly open the inlet valve, so
that the material enters the housing until the liquid overflows
from the bleeder valve at the top of the housing, at this time
close the bleeder valve. Pay attention to check the disassembly
place, whether there is leakage;.11. Slowly open the filter outlet
valve until it is completely open. Indicates that the replacement
is complete.12. Remove the tools used for replacement and cleaning
tools. Clean up the surrounding area.---Bag filter instalation
step 1. First of all, it is necessary to confirm whether the
accessories required for the installation of bag filter have been
prepared;2. Check the O-ring seal and the O-ring groove on the bag
filter in order to replace the accessories in time;3. When
installing the bag filter, it is necessary to place the bag filter
on the work station that needs to be filtered. After connecting the
inlet and outlet flanges or pipe teeth, fix the filter, smother the
exhaust port, or configure the exhaust valve, and the jacket type
connects the thermal insulation heat source;4. Slowly put the metal
m
Related products about Modified PVC Ultrafiltrate Membrane Filter 250series
- Waste Tyre Plastic Recycling Machinery Machine Tire Crusher Production Line Rubber Crumb Grinding Machine Equipment Tire Shredder
- Stretch Plastic Blowing Pet Bottle Making Blow Molding Machine Bottles Stretch Automatic Pet Bottle Blowing Machine
- Waste Plastic Pet Bottle, Water Bottle Flake, PP/HDPE/LDPE PE Film Jumbo Woven Bags Plastic Crusher Machine, Plastic Crushing Washing Recycling Machine
- Type 2 Wall-Mounted Electric Car Charging Station 7kw /11 Kwelectric Vehicle Charging Station Home Wallbox AC EV Charger Single Phase or 3three Phase
- G-View G12W Wholesale Auto Car LED Headlight Bulb High Power H13 H11 9005 H7 H4 Car LED Headlights LED Car Lights
- New Design Porcelain Round Plates Dinner Set for Wedding and Banquet
- China 2023 New Design Super Soft 100% Polyester Microfiber Knitted Oversized Decoration Hoodie Blanket
- Handmade Art Creative Materials Thickened White Paper Cup DIY Disposable Handmade Colored Paper Cup