Premium Activated Carbon Filter Cartridge CTO Series

Product DescriptionActivated carbon filter cartrdge CTO series are formed using extruding carbon fines and food-grade binders.This makes it FDA approved for the Food/Beverage industry. It also ensures that no bad taste is left behind. This filter is also great for filtering organicmatter effectively. Product Parameters  Products measures[Precision]: 5um,10um[Length]: 9.87"(250mm), 10"(254mm), 20"(508mm)[OD]:ø65mm, 70mm, 114mm[ID]:ø028mm, 30mmStructure material[Filter media]:Granular Activated Carbon [End cap]:Polypropylene[Gasket/Seal]:Silicone rubber, ethylene propylene rubber, nitrile rubber[Meshes]:PolypropyleneOperation data[Maximum Operating Temperature]:52°C[Maximum Differential Pressure]:7.0Bar@20°C     Our Advantages★ Good adsorption capacity.★ Remove efficiently the chlorine, peculiarsmell, organics. ★ Low pressure drop,steady flow.★ No carbon fine releasing.  Detailed Photos  Plant photoPackaging & ShippingCustomer site  Certification and test report FAQ---Replace the filter cartridge step1. Receive the production instruction to replace the cartridge and confirm that the system has stopped running.2. Prepare the appropriate filter element (specification, material, size, O-ring material, type, etc.), disassembly tools, collection bucket, rags, etc.; and3. Thoroughly clean the filter housing, empty around the filter, and leave the operation area. Take protective gears with you.4. Disconnect the filter to be replaced from the system. Slowly open the exhaust port at the top of the filter and depressurise it, paying attention to safety in the process to prevent material or liquid from splashing.5. Empty the material in the filter, open the filter cover with a tool, take out the filter cartridge, and pack the cartridge in a plastic bag to be scrapped; 6 Use clean tools and rags to clean the filter.6. Use clean tools and rags to clean the inside of the filter and install the new cartridge.7. Open the plastic bag at the open end of the filter element and check whether the O-ring is intact and in place.8. Install the inflow of materials according to the method of inflow from the outside of the filter element and outflow from the inside of the filter element.9. with the appropriate wetting agent (such as water) wet O-ring and cartridge seat jack, hand-hold the cartridge near the end of the O-ring, vertically insert the cartridge cartridge socket completely into the cartridge seat jack, the cartridge inserted, remove the cartridge bag, and then install the metal cover, with tools to tighten the filter; 10 close the filter drain port, open the plastic bag, open the filter, the filter is complete, in place.10. Close the liquid discharge port of the filter, open the bleeder valve at the top of the housing, slightly open the inlet valve, so that the material enters the housing until the liquid overflows from the bleeder valve at the top of the housing, at this time close the bleeder valve. Pay attention to check the disassembly place, whether there is leakage;.11. Slowly open the filter outlet valve until it is completely open. Indicates that the replacement is complete.12. Remove the tools used for replacement and cleaning tools. Clean up the surrounding area.---Bag filter instalation step 1. First of all, it is necessary to confirm whether the accessories required for the installation of bag filter have been prepared;2. Check the O-ring seal and the O-ring groove on the bag filter in order to replace the accessories in time;3. When installing the bag filter, it is necessary to place the bag filter on the work station that needs to be filtered. After connecting the inlet and outlet flanges or pipe teeth, fix the filter, smother the exhaust port, or configure the exhaust valve, and the jacket type connects the thermal insulation heat source;4. Slowly put the metal mesh basket into the bag filter, so that the collar of the mesh basket and the interface of the bag filter can be matched;5. Place the liquid bag filter, so that the bag filter bag ring mouth as well as the metal mesh basket collar can match;6. Place the O-ring seal into the O-ring groove, O-ring seal can not be twisted or deformed;7. After aligning the top cap of the bag filter, tighten the two diagonal hanging caps at the same time, and then tighten all the hanging caps afterwards;8. Close the exhaust valve installed on the top of the bag filter;9. Check whether each connecting pipe is firm and whether the working pressure is within the permitted range;10 slowly open the input valve, so that the liquid can slowly flow into and fill the filter, to prevent the liquid from suddenly impacting the filter bag, resulting in the rupture of the filter bag, and then observe whether there is a leakage phenomenon, if there is no leakage phenomenon can be found directly for filtration.---Bag filter replacement cycle PP Bag filter is a kind of water treatment equipment, the filter is often used in some water treatment process pretreatment, is an important pretrea