Product DescriptionGwc-C Full-Automatic Steel Bar Mesh
Welding Equipment Machine1.Wire Pay-off Mechanism The
pay-off mechanism includes the base, the discharge trays, the brake
mechanism, etc. Bearings are installed between the base and the
turntable, so that the turntable can be flexibly rotated when it is
working, and the brake mechanism can adjust the flexibility of the
turntable when there is no material discharged.In such case, the
coil will not automatically spread. The single pay-off tray can
bear 1200KG,but suggest 500-600kg loaded during working.
2.Line Wire Detecting Line
wire detecting includes guild frame, material shortage detection,
etc. When the line wire coil is used up, the machine will stop and
alarm automatically, and the operation screen will show the lack of
material.3.Straightening Mechanism The
straightening mechanism includes base,frame,straightening rollers
and guiding mechanism. The straightening roller includes a
horizontal straightening roller and a vertical straightening
roller, half of which are installed on the slider.It needs to be
adjusted to a suitable position so that it can make the
straightening4.Traction Storage Mechanism The
traction storage mechanism mainly includes:traction pressure
wheel,storage rack,the detecting device etc. The wires passing
through the straightening mechanism are provided with traction
force by the pressure wheel traction mechanism and sent to the
storage rack. Detecting device is designed on the upper and lower
sides of the storage rack to ensure that there are line wire to be
provided to the host for welding purpose.5.Stepping MechanismThe
stepping mechanism mainly includes stepper traction components,
precise straightening elements and conduit etc.. Stepping traction
is realized by clamping the wire through two sets of upper and
lower pressing rollers, and the roller is driven by the servo motor
to pull the wires and control the spacing of the cross wire. The
precise straightening elements straighten the wires by adjusting
two sets of straightening rollers and it assures the quality of the
mesh. The function of the conduit is to make sure straightness of
wires.6,WelderIt is composed of frame, air reservoir, pressurized
cylinder, lifting device, welding transformer, cross wire terminal
alignment part,cross wire detection device,cross wire adsorption
device etc. . It is key part of the whole line.The line wires enter
the welding area through guiding elements, and the cross wire is
adsorbed to the space between the upper and lower electrodes by the
magnet after falling into the welding area through the action of
the blanking mechanism.when the cross wire detecting device detects
the wires in place,the alignment valve acts which will make the
length of cross wires terminals alignment. Then the pressurized
cylinder is activated,the welding transformer discharges and welds
according to the set current and time. After the welding is
completed, the pressurized cylinder returns. 7,Cross Wire Blanking
MechanismThis part is mainly composed of material bench,material
adsorption roller, section wheel, pusher rod etc.. Firstly,put the
pre-processed cross wire into the material bench,then divide the
wires to pusher rod by material adsorption roller and section wheel
and send them to the electrodes rapidly.8.Cut & Shearing Mechanism
This part is used for shearing
the mesh according to the product length.The mesh spacing and
shearing position can be set through control panel according to the
specifications.9.Mesh turning over mechanismIt consists of servo
motor, balance weight lever, rotating arm, turning over frame,
gripping hook, etc. The mesh from output mechanism will drop to the
turning over frame,then the hook acts and fixes the mesh, the servo
motor drives the rotating arm, lifts the frame and the mesh, and
falls back to the initial position.After that the hook will be
released, and the mesh falls into the roller for stacking.10.Mesh
StackingIt includes unloading rack,conveyance roller etc. The
stacked meshes will be sent to packing area for winding and
transportation11, Electrical Control System This system includes
high voltage distribution cabinet and low voltage distribution
cabinet one for each,one operation control bench for controlling
the pneumatic circuit of welding and production line. 12, Water
Cooling System Cooling water system are composed by 4 parts:
transformer water cooling,upper-down water cooling,control box
cooling.It assures the normal working of device and avoid any
damage. 13, Pneumatic System It is equipped with air filter device
for purifying the compressed air and has a muffler. The air
reservoir is adopted to separate the impurity like dust,water and
oil from the air. F.R.L (XMC)and Pneumatic electromagnetic valve(
made in Taiwan) are used in this device. Product Parameters
Name Parameter Main Units 1. Line Wire Pay Off 2. Line Wire
Detection 3. Line Wire Straighteni
Related products about Steel Bar Wire Mesh Welding Machine Steel Reinforcement Wire Mesh Welded Equipment
- Waste Tyre Plastic Recycling Machinery Machine Tire Crusher Production Line Rubber Crumb Grinding Machine Equipment Tire Shredder
- Stretch Plastic Blowing Pet Bottle Making Blow Molding Machine Bottles Stretch Automatic Pet Bottle Blowing Machine
- Waste Plastic Pet Bottle, Water Bottle Flake, PP/HDPE/LDPE PE Film Jumbo Woven Bags Plastic Crusher Machine, Plastic Crushing Washing Recycling Machine
- Type 2 Wall-Mounted Electric Car Charging Station 7kw /11 Kwelectric Vehicle Charging Station Home Wallbox AC EV Charger Single Phase or 3three Phase
- G-View G12W Wholesale Auto Car LED Headlight Bulb High Power H13 H11 9005 H7 H4 Car LED Headlights LED Car Lights
- New Design Porcelain Round Plates Dinner Set for Wedding and Banquet
- China 2023 New Design Super Soft 100% Polyester Microfiber Knitted Oversized Decoration Hoodie Blanket
- Handmade Art Creative Materials Thickened White Paper Cup DIY Disposable Handmade Colored Paper Cup