Product DescriptionMBR is a combination of membrane technology and
bio-chemical reaction in water treatment. MBR filter
the sewage in bio-chemical tank with membrane so that sludge and
water are separated. On one hand, membrane rejects microorganisms
in the tank, which greatly increase the concentration of activated
sludge to a high level, thus the bio-chemical reaction of sewage
degradation processes more rapidly and thoroughly. On the other
hand, water output is clear and of high quality because of high
precision of membrane.This product adopts reinforced modified PVDF
material, which will not peel or break during
backwashing, meanwhile it has good
permeable rate, mechanical performance,
chemical resistance and anti-fouling
ability. ID & OD of reinforced
hollow fiber membrane are 1.0mm and 2.2mm respectively, filtering
precision is 0.1 micron. Filtering direction
is outside-in, that is raw
water, driven by differential pressure, permeates
into the hollow fibers, while bacteria, colloids, suspended solids
and microorganisms etc. are rejected in the membrane
tank. Product Parameters SLMBR-25 technical
detailsModel SLMBR-25Filtering directionOutside-inMembrane
materialReinforced modified PVDFNominal membrane area25m2Filament
diameter ID1.0mm,OD 2.2mm Out
size785mm×2000mm×40mmConnection sizeDN32
Component Material:ComponentMaterialHollow Fiber
MembraneReinforced Modified PVDFSealing CompoundEpoxy Resins +
Polyurethane (PU)HousingABS
Using ConditionsProper pretreatments
must be set when
raw water contains
a lot of impurities/coarse particles or
large proportion of grease. Defoamer must be used to remove
foams in membrane tank when necessary,
please use alcoholic defoamer which is not easy to
scale.ItemLimitRemarkPH Range5-9 (2-12 when washing)Neutral PH is
better for bacterial cultureParticle Diameter95%★ High
strength:>2000CN★ Long service life: Use imported PVDF raw
material, which has
goodchemical resistance, good hydrophilicity,
anti-agingability,
long service life. Application★ Municipal
sewage upgrade ★ Integrated water treatment
equipment ★ Industrial wastewater
upgrade ★ Refuse leachate treatment Detailed
Photos Plant photo Packaging & ShippingCustomer
site Certification and test report FAQ---Replace the
filter cartridge step1. Receive the production instruction to
replace the cartridge and confirm that the system has stopped
running.2. Prepare the appropriate filter element (specification,
material, size, O-ring material, type, etc.), disassembly tools,
collection bucket, rags, etc.; and3. Thoroughly clean the filter
housing, empty around the filter, and leave the operation area.
Take protective gears with you.4. Disconnect the filter to be
replaced from the system. Slowly open the exhaust port at the top
of the filter and depressurise it, paying attention to safety in
the process to prevent material or liquid from splashing.5. Empty
the material in the filter, open the filter cover with a tool, take
out the filter cartridge, and pack the cartridge in a plastic bag
to be scrapped; 6 Use clean tools and rags to clean the filter.6.
Use clean tools and rags to clean the inside of the filter and
install the new cartridge.7. Open the plastic bag at the open end
of the filter element and check whether the O-ring is intact and in
place.8. Install the inflow of materials according to the method of
inflow from the outside of the filter element and outflow from the
inside of the filter element.9. with the appropriate wetting agent
(such as water) wet O-ring and cartridge seat jack, hand-hold the
cartridge near the end of the O-ring, vertically insert the
cartridge cartridge socket completely into the cartridge seat jack,
the cartridge inserted, remove the cartridge bag, and then install
the metal cover, with tools to tighten the filter; 10 close the
filter drain port, open the plastic bag, open the filter, the
filter is complete, in place.10. Close the liquid discharge port of
the filter, open the bleeder valve at the top of the housing,
slightly open the inlet valve, so that the material enters the
housing until the liquid overflows from the bleeder valve at the
top of the housing, at this time close the bleeder valve. Pay
attention to check the disassembly place, whether there is
leakage;.11. Slowly open the filter outlet valve until it is
completely open. Indicates that the replacement is complete.12.
Remove the tools used for replacement and cleaning tools. Clean up
the surrounding area.---Bag filter instalation step 1. First
of all, it is necessary to confirm whether the accessories required
for the installation of bag filter have been prepared;2. Check the
O-ring seal and the O-ring groove on the bag filter in order to
replace the accessories in time;3. When installing the bag filter,
it is necessary to place the bag filter on the work station that
needs to be filtered. After connecting the inlet and outlet flanges
Related products about Mbr Membrane Module Reinforced PVDF Slmbr-25 Waste Water Treatment
- Waste Tyre Plastic Recycling Machinery Machine Tire Crusher Production Line Rubber Crumb Grinding Machine Equipment Tire Shredder
- Stretch Plastic Blowing Pet Bottle Making Blow Molding Machine Bottles Stretch Automatic Pet Bottle Blowing Machine
- Waste Plastic Pet Bottle, Water Bottle Flake, PP/HDPE/LDPE PE Film Jumbo Woven Bags Plastic Crusher Machine, Plastic Crushing Washing Recycling Machine
- Type 2 Wall-Mounted Electric Car Charging Station 7kw /11 Kwelectric Vehicle Charging Station Home Wallbox AC EV Charger Single Phase or 3three Phase
- G-View G12W Wholesale Auto Car LED Headlight Bulb High Power H13 H11 9005 H7 H4 Car LED Headlights LED Car Lights
- New Design Porcelain Round Plates Dinner Set for Wedding and Banquet
- China 2023 New Design Super Soft 100% Polyester Microfiber Knitted Oversized Decoration Hoodie Blanket
- Handmade Art Creative Materials Thickened White Paper Cup DIY Disposable Handmade Colored Paper Cup