Canopen K1 Series Servo motor Controller for Screw Machine

Basic Info.ApplicationIndustrialSpeedHigh SpeedNumber of StatorThree-PhaseFunctionDriving, ControlCasing ProtectionProtection TypeStarting ModeVariable Frequency StartingCertificationISO9001, CCCTrademarkSTEPTransport PackageCartonOriginShanghai ChinaHS Code9032899090Product DescriptionCanopen K1 Series Servo motor Controller for Screw MachineProduct Advantage:Intelligent· Powerful internal position mode allows for continuous multi-path planning for rich motion control; supports up to 32 data sets for planning, each set of data can be set to the number of pulses or angle required, and internal position mode can be set for speed, acceleration, deceleration and emergency deceleration· Automatic determination of load inertial mechanical properties, setting optimal gain and shortening system commissioning timeStable· Mechanical resonance frequency analysis, configured with two sets of trap filters, adjustable frequency (50 ~ 5000Hz) and trap depth, effectively overcome low frequency resonance and mechanical end vibration, vibration frequency (1 ~ 100Hz) and vibration damping can be setMultifunction· Frictional torque compensation reduces the effect of static friction during mechanical commutation and improves command following performance at low speeds· Multibus support: CANopenEasy to Operate· Support for debugging software, mechanical characteristics analysis, parameter setting, monitoring and other functions, intuitive and simple operationSpecifications:Bitmap   Moudle K1AS02K1AS04K1AS08K1AS15K1AS22K1AS30K1AS50K1BS15K1BS25K1BS35K1BS55K1BS750.2KW0.4KW0.75KW1.5KW2.2KW3KW5KW1.8KW3KW3.8KW5.5KW7.5KWInput PowerControl ModeThree-phase PWM converter sine wave driveMain Power220V: Single-phase/three phase 220V AC(-15~+10%,50~60Hz)380V: Three-phase 380V AC(-15~+10%,50~60Hz)Control power 220V: Single-phase 220V AC(-15~+10%,50~60Hz)Rated current220V:0.2KW/2A,0.4kW/2.8A,0.75kW/5.5A,1.5kW/10A, 2.2kW/12A,3kW/16A,5kW/25A380V: 1.8kW/5A,3kW/8A,3.8kW/12A,5.5kW/16A, 7.5kW/20A Encoder feedback ABZ incremen encoder / absolute encoderEnvironment Working temperature 0~45°CStorage temperature-20~65°C Working humidity20~85%RH or less (non condensing)Storage humidity20~85%RH or less (non condensing)Working and storage airndoor (no direct sunlight), non-corrosive gases, flammable gases, oil mist, dustAltitudeBelow 1000mVibration5.8m/s² (0.6G) below 10~60Hz (Cannot be used continuously at resonant frequency)Insulation andpressure resistancePrimary- between F and G, 1 minute under AC1500VFunctionsIO Input4-channel (DC24V optocoupler isolation) Input function can be selected according to parameters below: Servo on, P action, positive rotation inhibit, negtive rotation inhibit, alarm reset,positive torque limit, negtive torque limit, error clearIO Output3-channel optocoupler isolated output; the following output function can be selected according to parameters: Alarm output, position proximity, velocity consistent detection output, motor rotation detection, servo ready, torque limit, brake releasePulse inputDifferential input: 500K; open collector: 200KPulse + direction, AB orthogonal pulse, CW+CCW pulsePulse outputPhase A, phase B: differential output. Phase Z: differential output or open collector outputInternal speed command Three-speed distribution via input terminalsOverload CapacityMax. 3 times torqueAnalog input2-channel differential input ±10V, 1-channel single-ended 0-10V; switch according to control modeCommunicationModbus; Customized CANControl modes 12 control modes: position control, speed control, torque control, inner spped, position/speed control,position/torque control, speed/torque control, inner speed/position, inner speed/speed,inner speed/torque, speed/zero clamp, position control/command inhibitRegenerative resistance 400W: without external regenerative resistance; over 750W: with Quality management System1.Procurement Control ProceduresSelect qualified suppliers to ensure that material quality can satisfy usage request. 2.Production Process FlowEach staff is required to pass the qualification test for the job position and work in strict accordance with the process documents. 3.Quality Control ProceduresA wide range of measure are applied to control quality and they are:factory audit,signing quality agreement with suppliers,incoming materials inspection,first product confirmation,inspection during production,final inspection,production process analysis and improvement,corrective and preventive actions.Application:3C electronic equipment Packaging equipmentPrinting equipmentCNC Machine toolsTextile industryCompany:Company Environment:Certificate:Laboratory:Culture: