Adjustable Lux and Delay Time Ceiling PIR Sensor Light Switch

Adjustable Lux and Delay Time Ceiling PIR Sensor Light SwitchOur infrared sensor switch has pyroelectric infrared sensor (PIR), ambient-light detection sensor and control module in one unit. The device automatically turns light ON/OFF when it detects motion and ambient light level. It is ideal for business use of convenience, energy efficiency, and security. It can be used in hotel aisles, stair hall, balcony, garage, classrooms, libraries, offices, meeting rooms, hospitals, warehouses, manufacturing places, factories, etc. This product has an adjustable time delay from between 50 seconds and 9 minutes, along with light sensitivity adjustment from 2 to 1000 LUX.Automatic Detection TechnologyWhen a person passes into or out of a sensor zone, the sensor detects motion and switches the lights ON. The lights will remain ON as long as there is an occupant in the room. When the space being monitored by the sensor is unoccupied for the preset time you've entered, the unit will switch the lights OFF.Sensitivity, Time Delay AdjustmentWhen ambient light level lower than the preset setting, the sensor switch goes into normal operation. With adjusting SUN1, users can adjust the sensor switch from 5~500 LUX to adapt the actual need. The product also has an adjustable time delay from between 16 seconds and 350 seconds.Curved DesignThe design inspiration prevents the conflict feeling of the less curved design. Because of the curved design, and it is attached to the ceiling, it brings relaxed and natural feeling.Dual Inductive Control (Import PIR, Photosensitive Control)RE200BP PIR with high sensitivity and stability; energy saving photoresistance control, light only on when lighting is below set point as to achieve energy saving purpose.Pyroelectric Infrared Processing ChipBISS001 pyroelectric infrared processing chip with stable and reliable performance. It also possesses relay control load with high-peaked and stable contact.Honeycomb Lenses for Superior Occupancy DetectionTaiwan imported honeycomb lenses offers higher sensitivity and wider detection range option than other similar products.Ultralow-power ConsumptionSelf-power consumption within 0.026w/h, much more energy saving compared with similar products.Lightening Protection FunctionSpecial-made lightening protection device, effectively prevent high-pressured instant damage to the switch.Easy InstallationFirstly, use 2 screws to secure the mounting box to the ceiling. Then drill a hole next to it, thread the wires through the hole, and match the sensor switch with the mounting box.Product Internal DetailsWiring DiagramInstruction1. Install following the wiring diagram, after the careful check, connect the power supply. 45 seconds is needed for preheat. When a person passes into or out of a sensor zone, the sensor detects motion and switches the lights ON.2. Product sensitivity is set up automatically from factory. No need for adjustment if not installed in special location.3. Time delay adjustment: turn the timer rightward, extend time delay; leftward, then otherwise.Attention1 Disconnect electricity in wiring process; prevent over-loading short-circuit; put on electricity after installation.2. Strictly follow the wiring installation diagram. Incorrect wiring would cause power supply line fault and damage to the switch.3. Strictly forbidden to use in super power or it would also cause damage to device.4. Please install the unit in the center of the detected area; avoid blocking the lenses to achieve maximized detection range. In addition, please install in the area with average lighting. If installed in shady coner, sensitivity of the sensor switch would be lower than the average ambient light, and the sensor would not switch the light on in faint sunlight. The sensor switch must avoid direct lighting from the lenses or it might cause flashing to the light.5. In order to keep the high sensitivity, please install the sensor at least one meter away from the laader; please do not install the product in strong light environment and where there is strong cold or heat airflow; please also do not install near high-power radio-frenquency radiation (such as radio, interphone, antenna, etc.)ParametersOperating voltage AC100-240V±10%Detecting distanceHeight 2.5~4 meters, Radius3~5 metersInstallationCeiling-mountedLoad typeIncandescent light bulb, fluorescent lamp, compact fluorescent lamp, LED, etc.PowerMax. 0.5WCapability of loadMax. 1000WViewing area360° degree field of viewLighting detecting range 2~1000 LUXTime delay50 seconds~9 minutes (adjustable)Environment temperature -20ºC~60ºCShapeΦ89x36mmReliable qualityLasts more than 500,000 times  /* January 22, 2024 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(",").forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1