High Cost Effective Electrospinning Electrospinning & DIY Electrospinning Unit

High cost-effective electrospinning electrospinning & diy electrospinning unitI. INTRODUCTION1A high voltage power supply is a high precision, high stability high voltage power supply with positive or negative polarity output in a range of sizes, with output voltages from 0 to 130KV and maximum output power of 10000W.2The output voltage and current values are displayed on a digital meter on the panel for easy operation. The output voltage can be continuously and linearly adjusted by the user via the potentiometer knob. 3The power supply is protected against over-voltage, over-current, arc pull, and short circuits. 4The power supply has a metal casing with a good electrical shielding effect.II. APPLICATION1Electrostatic Separation12Electrostatic Spraying2Capillary Electrophoresis13Electrostatic Flocking3Electrostatic Dust Removal14Old Refining Equipment4Pressure Resistance Testing15Electrostatic Spinning5High-Pressure Bias16High-Pressure Deburring6High-Pressure Ignition17Material Sorting7Metal Vaporization18Electric Explosion8Air Purification19Water Purification9Electron Beam20Medical Sterilization10Communication And Transportation21Scientific Research11National Defense22 .....III. FEATURES1High stability, high accuracy, and small size.2Continuous linear adjustment of the output voltage.3Adjustment of the local control potentiometer.4Protection functions for over-voltage, over-current, arc pulling, and short-circuit.5Start and stop function6Low EMI, high anti-interference capabilityPRODUCT LISTPower supply models/Output voltage range0~+130KVDC &0~-130KVDCRated output current1mARipple noise≤1%Voltage regulation rate≤0.1%Load Adjustment Rate≤0.5%SPECIFICATIONTechnical specificationSpecification indicatorInput voltageAC90V~AC264V,47Hz~63HzOutput voltageSee "List of typical high voltage power supplies" for details, customised to suit customer requirementsOutput currentOutput power≤300WRipple voltage≤0.5%Voltage regulation rateLess than 0.1% within the maximum permissible range of input voltage for a given loadLoad Adjustment RateInput voltage constant, load from no-load to rated, less than 0.5%Time-drifting≤0.1%/h (after 30 minutes of power operation)Warm float≤0.1%/ºCThis controlThe output voltage can be set between 0V and the maximum voltage by adjusting the multi-turn potentiometer.Start/stop functionControls the start and stop of the power supply; when the switch is "pressed", the power supply is activatedGrounding methodAC isolated, reference ground to earthProtection methodFlow limiting typeOperating temperature range0ºC~+50ºCStorage temperature range-25ºC~+75ºCNet Weight3.0KGHousing materialAluminiumDimensionL300*W260*H45(MM)FORM FACTOR AND DIMENSIONSMAIN FUNCTION DESCRIPTIONWIRING DIAGRAMPRODUCT OVERVIEW INSTALLATION & NOTESThis product is a high voltage power supply. Please be sure to operate it correctly and take safety precautions, otherwise, electric shock accidents and property damage may occur. Please read the following precautions carefully.1Place the power supply on a horizontal surface for use.2Ensure that the power supply is reliably earthed before use.3Please keep the output of the power supply at a certain insulating distance from the surrounding components to avoid discharge.4To ensure reliable operation of the product without overheating and high temperatures, blocking and covering the ventilation holes and keeping away from heat sources are strictly prohibited.5The use of the power supply should be avoided in dusty or humid environments, otherwise, the insulation will be reduced and partial discharge will occur.5It is strictly forbidden to disassemble and repair the high-voltage power supply to avoid personal injury and economic loss caused by high-voltage power supply failure.6It is strictly forbidden to operate or repair the internal circuit of the high-voltage power supply with electricity, as dangerous or even fatal voltages can be generated inside the power supply.7Do not touch the high voltage connectors unless the load and the capacitors inside the power supply have been completely discharged after switching off the high voltage power supply.8It is strictly forbidden to insert other objects into the ventilation holes of the equipment to avoid accidental contact with the circuit, short-circuiting, causing fire or electric shock.IV. MODEL SELECTION 1KVNOModelOutput voltage(KV)Output Current(mA)Output Capacity(W)#1IPS-ATDWSDL1-101KV10mA10W#2IPS-ATDWSDL1-301KV30mA30W#3IPS-ATDWSDL1-601KV60mA60W#4IPS-ATDWSDL1-1001KV100mA100W#5IPS-ATDWSDL1-1501KV150mA150W#6IPS-ATDWSDL1-3001KV300mA300W#7IPS-ATDWSDL1-6001KV600mA600W#8IPS-ATDWSDL1-12001KV1200mA1200W2KVNOModelOutput voltage(KV)Output Current(mA)Output Capacity(W)#1IPS-ATDWSDL2-52KV5mA10W#2IPS-ATDWSDL2-152KV15mA30W#3IPS-ATDWSDL2-302KV30mA60W#4IPS-ATDWSDL2-502KV50mA100W#5IPS-ATDWSDL2-752KV75mA150W#6IPS-ATDWSDL2-1502KV150mA300W#7IPS-ATDWSDL2-3002KV300mA600W#8IPS-ATDWSDL2-6002KV600mA1200W3KVNOModelOutput voltage(KV)Output Current(mA)Output Capacit