Contitech Fs530-14cig3/4OS Fire-Stone W01-M58-6369 One Convoluted Industrial Suspension Air Springs

Contitech FS530-14CIG3/4OS Fire-stone W01-M58-6369 One Convoluted Industrial Suspension Air Springs  Cross Reference CONTITECH FS 530-14CONTITECH FS 53014CONTITECH FS 530 14Continental FS 530-14Contitech FS 530-14 CI G 3/4 OSContitech FS530-14CIG3/4OSContitech 66897Fire-stone W01M586369Fire-stone W01 M58 6369Fire-stone W01-M58-6369Fire-stone WO1M586369Fire-stone WO1 M58 6369Fire-stone WO1-M58-6369Goodyear 1B14-372Goodyear 1B14 372Goodyear 1B14372  Specifications and Detailed Technical Parameters:AIRSUSTECH 1B53014-3/4 Industrial Suspension Air Spring One Convoluted; 4 X M8 Blind Nut/Nut; 158.8mm Screw Center Distance; G3/4 Offset Air Inlet; Female Mounting Threads; Without bumper block and Girdle hoop  Storage and Maintenance Storage1. When storing the air spring, please store it in a low temperature and dark place with poor ventilation as much as possible, and avoid direct sunlight.2. Please avoid letting the air spring stick to oil and medicines. If adhesion is left unattended, durability may be reduced due to reduced physical properties of the rubber.3. The wall thickness of the air spring is relatively thin, about 5mm. Please be careful to avoid scratches etc.4. The air spring is ideally stored in a free state.5. Do not place it in a place with a temperature above 50°C.Maintenance and InspectionFor air springs, daily inspection and safe use must be done. If abnormality is found after inspection, it must be replaced with a new one immediately.1. Before using the air spring, it is necessary to confirm whether the upper and lower panels and the waist ring are installed correctly, especially the waist ring. If the rubber film is subjected to internal pressure when the waist ring is offset or fallen off, the rubber film will be ruptured.2. When impurities, oils, medicines, etc. adhere to the air spring, please be sure to remove it.3. If the lubricating oil enters the inside of the air spring, it must be wiped frequently, and the inside of the air spring should be washed with water regularly.4. Please confirm whether the appropriate pressure can be provided when using, especially in many cases, the piping system will be abnormal, please pay attention.5. In the following cases, please replace the air spring.• Cracks, scuffs, abrasions in the outer rubber that can reach the reinforcing cord layer.• If the air spring is abnormally deformed or expanded, even if there is no trauma, air will accumulate inside the air spring, resulting in separation.• The rubber surface swells or cracks due to oil, chemicals, heat, etc.6. If the upper and lower panels and waist ring are corroded, the air spring will be scratched. Therefore, the corroded parts must be replaced. The related picture of 1B53014-3/4Company Profile Guangzhou Guomat air spring Co., Ltd. was established in 2008 and is located in Guangzhou, the capital city of Guangdong Province. The company's production plant covers an area of 20,000 square meters and is located in Taihe Town, Baiyun District, Guangzhou City. With the continuous development of the company, it is gradually equipped with modern workshops and advanced rubber air spring equipment. It is one of the important air spring production bases in China. At the same time, Gomart used domestic advanced air spring processing equipment and introduced foreign air spring production technology, combined with the company's unique production process, and strictly implemented production in accordance with international standards to produce advanced products. All products comply with ISO9001, ISO/IS16949 standards.The main products of Guangzhou Guomat air spring Co., Ltd. are: rubber air springs, air suspension springs, rubber air springs for automobiles, airbags for passenger cars and trucks, industrial air springs, etc. The products cover buses, luxury cars, trucks, Commercial vehicles, rail vehicles, industrial machinery, industrial equipment and other industries. The company has hundreds of models and styles of products. At the same time, it can also carry out directional transformation and design of products according to the special needs of users, providing users with one-stop service.Factory workshopFAQQ1:Can you produce the product according to the samples?A: Yes, we can produce by your samples or technical drawings. We can build the molds and fixtures.Q2: What is your sample policy?A: We can supply the sample if we have ready parts in stock, but the customers have to pay the sample cost and the courier cost.Q3: What certification does your product pass?A: Our products are certified to ISO/TS16949:2009 international quality standards. Please rest assure that we have very strict Quality Control Systems.Q4 : Can I use my own logo?A:Sure. We can do as per the customer's requirements.  /* January 22, 2024 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(",").forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1