MAGIC TILT 56" Square Galvanized Boat Trailer Axle (1,500 lb.)

Square trailer axle beam measures 56" from hub face to hub face (when hubs - sold separately - are mounted) and 46-1/2" from spring center to spring center. E-Z Lube spindles make it easy to lubricate bearings (sold separately). Overall Length = 61" Hub Face = 56" Spring Center = Recommended 46.5" Capacity = 1,500 lbs. MAGIC TILT Factory OEM Axle weldment and hub assembly with 4-on-4" lug pattern. Lug nuts sold separately.  Features:Square axle beam acts as part of your trailer's suspension system Replace an axle on your trailerFabricate a suspension to fit your applicationHigh-strength steel constructionBend in axle creates zero camber angle for even road-to-tread contact across the width of your trailer's tires Best for straight-line acceleration and steady, controlled towingUnderslung design - spring seats welded to underside of axle for mounting leaf springs (sold separately) Low ride height makes it easier to load and unload your trailerStraight, E-Z Lube spindles - no drop Built-in grease zerks for simple lubricationSpring seats, brake flanges, and spindles are welded on  Universal replacement axle for trailers. Galvanized axle stock weldment only. Features a stainless steel wear sleeve. Wheel Hubs and bearings sold separately. MAGIC TILT factory OEM replacement trailer axle. Galvanized axle stock weldment and hub assembly with 4-on-4" lug pattern. Lug nuts sold separately. Axle weldment with spindles, spindle nuts & cotter pins. Wheel hubs & bearings sold separately.Specs: Axle Type: 1-1/2" x 1-1/2" Square Load Rating: 1,500 lbs. Overall Length: 61" End of Spindle to End of Spindle Spring Center: 46" (Pre-Drilled) Hub Face: 56" Hub Type: 4 bolt on 4" pattern Spindle Size: 1-1/16" x 1-1/16" Camber: No Camber (Due to Magic Tilt production changes, Axles with pre-installed hubs may be shipped with hubs featuring 1 of 3 finishes: Galvanized, Painted, or Zinc. This is at the manufacturers discretion so we will not be able to accommodate a choice in finish)  PNAxle TypeRatingHub Face to Hub FaceSpring Center To Spring CenterAxle SizeFinishSpindle SizeHub TypeCamberTSA011 1,500 lbs MAGIC TILT Trailer Axle Beam1,500 lbs56"46"1-1/2" x 1-1/2" SquareBlack Painted1-1/16" x 1-1/16"4 bolt on 4" patternNo CamberSELECTING THE PROPER TRAILER AXLE When selecting an axle for your application remember to consider the following important specifications:LOAD CAPACITY:  the load rating of the axle must support the maximum gross vehicle weight rating. For multiple axle trailers divide the GVWR by the number of axles to determine the minimum load capacity of each axle.TRACK LENGTH:  measure your axle track length by determining the distance between the center of one tire to the center of the other tire. A more precise measurement can be made by measuring the distance from one 'HUB FACE' to the other. The hub face is also known as the mounting surface where the wheel studs are located.SPRING CENTERS:  measure the distance from the center of one spring to the center of the other. NOTE: not required for replacement torsion axlesOVERALL LENGTH:  measure the distance from the very end of an axle's spindle to the very end of the opposite spindle.AXLE STYLE:  important when reusing old mounting hardware and also for proper tire clearance. Includes straight axles (round or square), drop axles with offset spindles, and torsion axles. Also consider spindle size when reusing existing hubs or drums.AXLE CAMBER:  Most trailer axles are designed with a bend in the tube that will deflect when the load (weight of the trailer) is applied. This will theoretically bring the trailer wheel camber toward a 0 value that is the best setting for most trailer applications. This will allow the tires to wear evenly and allow the longest tread life. Camber can be affected by damage to the axle. For example, if the axle spindle is bent, this will usually cause a negative camber on that side which will cause excess tread wear on the inside of that tire.   Ningbo Harsco Machinery Co., Ltd is a professional manufacturer of trailer parts in Ningbo, Zhejiang Province, China since 2016.   We can produce many trailer parts & accessories as follows: Towbars, axles, brake drums, hubs, brake disc, bearings, springs and springs and suspension kits, couplings, mudguards, U-Bolts, Jockey Wheels, keel rollers and brackets, wobble roller, wheel spacer, equalizers and all accessories related to trailers.If you can send me the drawings or specifications of the trailer parts, mechanical parts and wheels, we can give you our price.Q1: Do you have factory?A: Yes, we have our own factory, own engineers, we can meet custom's unique requirement.Q2: Can I have a sample order?A: Yes, welcome sample order to test and check quality. Mixed samples are acceptable.Q3: It's OK to print my logo on your product?A: Yes, we can according to your exact requirement.Q4:How do you ship the goods and how long does it take arrive?A: We usually shipped by DHL, UPS, FedEx, it usually takes 3-5 da