OEM Auto Wheel Hub Bearing for Toyota Lada Mitsubishi Nissan Isuzu Honda Mazda Hyundai KIA Daewoo Peugeot Mercedes Benz BMW VW Ford Gmc Chevrolet Chrysler Dodge

How long is the life of the car wheel hub bearing?The life of the car hub is determined by various factors, but usually check the hub wheel bearing after 50,000-80,000 kilometers:1. Comprehensively consider factors such as the quality of the bearing itself, vehicle driving conditions, mileage and load value;2. If the wheel bearing quality is good, the road conditions are flat (no high-frequency bumps), and the load is reasonable (not overweight), under normal circumstances there will be no problems (noise) within 15,000 kilometers;3. The theory of the front and rear wheel hub bearings of the car is 100,000 kilometers, but in the process of use, such as wading in summer, there is no half-wheel drive, which will directly affect the service life of the bearings. Therefore, in the summer rainy season, open as shallow a road as possible;4. The lubricating grease in the wheel hub bearing with good quality is water-resistant, but the fine dust particles in the water will accelerate the wear of the bearing, and the lubricating grease will reduce the water resistance for a long time;5. After the wheel hub bearing enters the water, oil, water and friction will make the lubricating grease turn into an emulsion and lose the original lubricating effect. The lack of lubricating grease in the bearing will accelerate the wear of the bearing needle roller and the inner and outer sleeve of the ball bearing, and the wheel bearing will make noise after a long time it came out.Let TAIZHOU DONGNA share the Ways to improve the service life of automobile wheel hub bearings:Grasp the lubrication, installation and sealing technology of the wheel bearing: first, when adding grease to the hub bearing, it is necessary to fully calculate the amount of grease added, avoid too much or too little, and ensure that the quality of the grease itself is passed and there is no foreign matter inside the grease. Specifically, the following aspects should be paid attention to:(1) Clean the wheel hub bearings. During maintenance, the hub bearings need to be thoroughly cleaned, and checked to ensure that the bearings are not broken, shed, cracked, or ablated, and then fully dry and free of moisture, otherwise the lubricating effect of the lubricating oil on the wheel hub bearings will be destroyed and the bearings service life will be reduced. (2) The wheel hub bearings are well lubricated. While the hub cavity is coated with a thin layer of grease to prevent rust, the wheel hub bearing must also be fully lubricated. It is necessary to ensure that the maintenance personnel squeeze hard by hand, and refill the rotating bearing repeatedly until the roller bearing is filled with grease, then the lubrication is complete, so as to ensure the good lubrication state and normal wear of the wheel hub bearing.(3) Strictly implement the maintenance procedures. During maintenance work, maintenance personnel must strictly abide by the requirements of technical specifications, clean, inspect, adjust, lubricate, and fasten various mechanism components to ensure maintenance quality and vehicle braking performance. Observe the operation status in real time. When the vehicle is in operation, coordinate the driver to pay attention to abnormal conditions such as abnormal noise, high temperature, and low braking performance of the wheels, collect information and deal with it in time to eliminate hidden troubles.Secondly, to do a good job of bearing installation, especially the adjustment of the wheel hub bearing clearance, the bearing manufacturer should pre-set the clearance before leaving the factory to avoid improper adjustment of the clearance during subsequent installation. Thirdly, in order to prevent impurities in the external environment from entering the bearing and causing excessive friction, scientific and effective sealing measures should be taken. Generally, the method of installing a sealing ring is used. In addition to strict sealing, the material of the wheel hub bearing sealing ring is also required. It must have sufficient heat resistance, and the installation of the wheel bearing sealing ring should preferably be pre-installed before leaving the factory.Product description OEM auto wheel hub bearing for Toyota LADA MITSUBISHI NISSAN ISUZU HONDA MAZDA HYUNDAI KIA DAEWOO PEUGEOT MERCEDES BENZ BMW VW FORD GMC CHEVROLET CHRYSLER DODGE    Item Name         Auto/car WHEEL BEARING,WHEEL BEARING HUB, WHEEL HUB BEARING, wheel hub unit,wheel bearing kit,pilot ball bearing,cross bearing spider kit,clutch release bearing,hub bearing assemblyOEM/REF NO.             43570-60011                42460-60010          2108-3103012                42450-52060                  90363-40066               90369-45003                90363-40079                  MR992374  Car ModelFor TOYOTA HONDA NISSAN HYUNDAI KIA MITSUBISHI ISUZU FORD GMC CHEVROLET CHRYSLER DODGE JEEP MAZDA PEUGEOT BMW VW MERCEDES BENZ POSITIONRH/LH/Right/ Left/ Front/RearMOQ50PCS/100PCS/150PCS/200PCS depend