Good Quality High Pressuer Water Oil Tank Truck Auomatic Wash

One ,The main technical parameters1,Equipment name:Tank and Garbage truck tunnel washing machine  2,Main technical parameters    2.1  Dominate machine size:11500×4000×4700mm (L x W x H)    2.2  Secondary machine size:11500×2350×2700mm (L x W x H)    2.3  Washable vehicle size:2500×3200mm (W x H)    2.4  Power supply:3Phase 5Wires 220V/50HZ,Total capacity 80KW,The highest use of power 80KW.    2.5  Water supply:Pipe diameter 50mm,Processing capacity 10m³/h,Washing pressure over 3kg.    2.6  Air supply:Air pressure 8kg.    2.7  Working environment:Maximum humidity 70%,environment temperature -2ºC-45ºC.    3,The main component materials3.1  Electric barriers:220V/50HZ,Manual control in and out the vehicle.3.2 The wheel cleaning system:Using the vertical multistage  centrifugal pump,Flow 260 L/min,Water pressure 12kg.    3.3 Chassis cleaning system:Using the vertical multistage centrifugal pump,Flow 70L/min,Water pressure 15kg.3.4  Lotion spray system:Use automatic matching regulator,The highest adjustable 150 times dilution ratio.3.5  Foam spray system:Use automatic matching regulator ,Moisture automatically produce bubble.    3.6  The vehicle head and tail of high pressure water spray system:Using horizontal plunger high pressure pump,Flow 120 L/min,Water pressure 60kg ,Start up by 15kw triangle type Siemens motor .     3.7  The first side of high pressure water spray system:Using horizontal plunger high pressure pump,Flow 120L/min,Water pressure 60kg,Start up by 15kw triangle type Siemens motor.    3.8  The second side of high pressure water spray system:Share a horizontal plunger high pressure pump with the vehicle head and tail cleaning system,Use the electric value to convert spray.    3.9  Air drying system:Four sets 7.5kw high powerful fan,Use fixed automatic air drying.3.10 Circulating water system:Sewage treatment: 10m³/h.    3.11 Electrical control operation system    3.11.1 Japan "Mitsubishi" PLC electrical control system .    3.11.2 Taiwan "Taida" touch screen operation system.    3.11.3 "Omron" electric detection,route detecting element.    3.11.4 Including administrative management functions:Including check alarm information and On that day and the number of cumulative wash the vehicle.Two ,Cleaning process        1,  Standby redundancy    1.1  Open the general supply,Ensure that the main engine water cycle and air compressor are in the state of power.    1.2  Check the vehicle washing machine is in standby state.1.2.1 The two lights of Washing wheel machine, the vehicle head and tail are displayed as the green light.1.2.2 The vehicle head and tail of the spray body spray rod vertically are able to open to both sides.    1.2.3 No other debris in the vehicle wash channel affect the vehicle washing.    2,cleaning process2.1 By rotating the "control power" knob in the control panel,Open the control cabinet to control the power supply,The whole set of vehicle  washing machine can be in the "clean vehicle" waiting state(waiting the vehicle enter.2.2 Manual opening entrance gate,Let the vehicle walk into the cleaning channel slowly,When the vehicle goes front wheel presses the induction plate of the washing machine, working indicator in the Washing wheel machine turn into a red light,The driver stopped immediately,strain the parkbrake. After 3-5 seconds,washing wheel machine starts to work,According to the procedures set cleaning time,After cleaning, the indicator light turns green(The first group of tire cleaning is completed).Attention:When cleaning the rear wheels(Most parts of the vehicles have entered in the car washing machine and have been in a state of cleaning),"Chassis cleaning" and "shampoo spray" section suspend working(Because the vehicle is stopped when the tire is cleaning), Other processes are not affected.When the vehicle is moving forward, "Chassis cleaning" and "shampoo spray" section continue to work.2.3 The vehicle moving on,When the two sets of photoelectric switches in the chassis position detect there is a car,then start working,So the vehicle moving forward while cleaning the chassis.When the head of vehicle enter into the "car head and tail" first group of photoelectric switch in the cleaning position,"Green light"in the Display working position flash;When the vehicle head enter into the second groups of photoelectric switch,"Green light" turned into "red light"(If the vehicle  move over the third sets of photoelectric switches,The "red light" flash,Vehicles need to reverse until the "red light" stops flashing and lighting up),The driver stopped immediately and strain the park brake,after pause 3-5 seconds,start spraying the vehicle head:High pressure water is sprayed out by the nozzle facing the vehicle head of spray rod,turn to center position at the same time,reach the middle position and then open to the two side,vehicle head cleaning finished,at the same time,indicator light turn into green light and stop spraying.Attention:when cleaning the vehicle head, "Chassis cleanin