Liquid Pressure Booster Pump Hydrostatic Test Bench Hydraulic Test Bench

Product DescriptionThe fluid pressurized control cabinet has been equipped with the fluid booster pump,the drive air water filter,the pressure regulator valve, Pressure gauges and manual pressure relieve valve. The main parts of the equipment are assembled in closed stainless steel cabinet or stainless steel frames. The pressure gauge,valve and pressure regulator will be mounted on the panel. The corresponding sign will also be marked on the panel. The ideal working high pressure can be achieved by adjusting the driving air pressure. When the driving air pressure and output pressure are balanced, The pump will automatically stop the filling pressure, and the output pressure will remain at the preset value.The hydraulic device can be used for pressure testing of various components, research and testing institutions and industrial pressure field.Booster pump have a variety of pressure ratios, These series of pumps are ideal choice for various hydraulic power operations. The maximum operating pressure up to 50000psi .The output pressure is produced by pneumatic booster pump, Therefore the electric connection will not be necessary.The structural design of the Fluid pressurized control cabinet are compact and according to the special requirement of customers, Combined the air driven fluid booster pumps,valves ,control switches and other precision accessories are assembled in the frame or closed cabinet.The pump will stop working automatically when the output pressure reaches the preset value, The pump will start automatically when the outlet pressure drops slightly or the air drive pressure increases.Product ParametersTEREK pumps feature is a large air piston joint to a smaller diameter piston. The pressure ratio is the difference of these two areas and is the method of determining maximum outlet pressure. Higher pressures obtained by using higher pressure ratios. TEREK model reflect the pumps nominal pressure ratios, while the technical data indicates exact ratios. The outlet pressure is easily to set through a simple regulator. By multiplying the pressure ratio by the available shop air pressure, the nominal liquid pressure can be calculated. Basically the principle of operation is similar to a reciprocating amplifier where control of the piston at the end position is reciprocating , The automatic reciprocating motion of the piston is controlled by a built-in four-way valve. TEREK pumps are air driven at a drive air pressure of 3 to 8 bar (29 to 116 psi) by the normal air compressor. LDD Series booster pump. Double acting, single air drive head Diameter of drive plunger is 160mm The diameter of the drive cylinder:160mm Drive cylinder stroke:50mm High pressure Cylinder stroke:50mm The maximum driving pressure of the drive air is 8 bar/116psiCommon Model Equipment Technical Specification IntroductionProduct namePneumatic liquid booster pump Hydrostatic pressure testing benchModelLU-LDD-100Pressure ratio100:1MediumHydraulic oil or waterDrive air source pressure3-8bar.Power sourceTEREK liquid booster pumpMaximum liquid outlet pressure800bar/11600psi.When adjusting drive pressure 5 bar The high output pressure is 500bar/7250psiWhen adjusting drive pressure 6.9 bar The high output pressure is 690bar/10000psiOutlet pressure Control unitDrive air regulator valvePressure control accuracyless than 1%F.S;Pressure measurement accuracy0.4 pressure gaugeValves and pipingHigh pressure needle valve and stainless steel pipingEquipment Frame type304 Stainless steel frame .Equipment Weight35 KGExportwooden case Weight45 KGEquipment Dimension500*370*520 mmPacking size:560*450*570 mmConnection size(inch) OutletNPT 1/4 Internal ThreadProduction time12-15 days.Delivery Method.Deliver the goods to your designated address by air express. Air transportation time5-7 days.Equipment Detailed ImagesSystem ConfigurationThe liquid booster pump mainly consists of air drive chamber, pressurizing chamber, auto reversing valve, inlet check valve, outlet check valve, High quality sealing parts, air drive piston, pressurizing piston, silencer etc. TEREK hydraulic test bench system mainly includes three sets of air driven liquid booster pump, 15L water tank ,pressure gauges, liquid filter ,air filter, air regulating valve,control valves,pipelines, cabinet , pressure release valve etc. The main parts of the equipment are assembled in closed stainless steel cabinet or stainless steel frames. The pressure gauge,valve and pressure regulator will be mounted on the panel. The corresponding sign will also be marked on the panel.Product Description1. Equipped with high quality pneumatic chemical reagent injection pump, It can easily achieve any adjustable and controllable output pressure and flow. 2.The contact liquid section is stainless steel, strong corrosion resistance, suitable for a variety of chemical reagents;3. It can be used at various levels of wellhead pressure, the pressure system has control function.4.Chemical reagent injection system outpu