Fully Automatic Lift / Elevator Board Painting Powder Coating Line,
High Quality Ce Approved Spray Paint Booth For Electric Lift
BoardProduct DescriptionThe coating line consists of a surface
pre-treatment machine, a drying and curing oven, powder coating, a
curing drying tunnel, a hanging conveyor, and an electrical control
system. Sprinkler System The spray device is composed of a spray
pump, a pressure relief valve, a pressure gauge, a spray main pipe,
a spray riser and a universal ball nozzle. The flow rate and
pressure of each pump can be adjusted through the throttle
adjustment valve and pressure gauge, and the pressure adjustment
range is 0.5 ~ 1.5Kg.f / cm2 The spray main is made of stainless
steel pipe; the spray riser is made of stainless steel pipe. The
film spraying section adopts W-type atomizing nozzles, and the
remaining spraying sections adopt V-type nozzles. The total amount
of nozzles is 960. The nozzle is made of polypropylene and has a
heat resistance and chemical stability. The liquid storage tank is
provided with alarms for the liquid level above and below, and is
interlocked with the spray pump. Storage tank blowdown valve
stainless steel wafer type butterfly valve. Tank The inner panel of
the tank is δ2.0mm thick SUS304, and the outer panel of all tanks
is δ0.8mm thick SUS304. The inside and outside of the heating tank
are insulated by 50mm thick high-quality rock wool, which has good
insulation performance. All tanks are equipped with double
stainless steel 10 mesh screen filters. Between the pre-greasing
and main degreasing tanks, water washing1 and pure water washing 1,
a connecting pipe is provided, and a DN65 galvanized steel pipe is
used. The countercurrent water replenishment method can improve the
cleaning effect and save resources. There are two slopes at the
bottom of all tanks, which can completely discharge the slag in the
tank. The inner plates of the tank are all through welding, and
after the water loading test, it is ensured that the welding is
firm and does not leak. The membrane tank is equipped with a set of
90 ton/hour bag filters. Pump system This system is equipped with 6
pumps. The outlet of the spray pump body is provided with a
pressure relief bypass, and the pump flow and pressure are adjusted
by a bypass valve. Valves and fittings The stainless steel spray
line uses stainless steel valves. A copper ball valve is used for
the water pipe. The pre-treatment spray branch pipe is connected
with the riser by a union. The connection between the pretreatment
supervisor and the supervisor, and between the supervisor and the
pump are flanged and bolted. All pipes can be easily removed.
Auxiliary equipment The pre-degreasing tank is equipped with a set
of the oil-water separator to remove the oil stains in the
pre-degreasing tank and effectively control the composition of the
tank liquid. relatively stable. A set of pipelines for driving the
degreasing tank liquid into the pre-greasing tank is also provided.
The silane tank is equipped with a set of automatic liquid adding
device, the main configuration is as follows: PH meter × 1 unit and
metering pump × 1 unit (preferred brand: Pasfida), and the medicine
is automatically added, which is a closed-loop system. The silane
tank is equipped with a stainless steel bag filter to remove
impurities in the tank and improve the utilization rate of the tank
liquid. All tanks are equipped with a lower limit alarm system to
prevent dry liquid from damaging the main spray pump. Rotor
flowmeters are all installed in the fresh pure water direct
injection pipelines, which can easily observe the specific water
consumption. The rotor flowmeters use domestic high-quality brands.
There is an artificial water blowing platform (1) and a compressed
air blowing gun at the pre-treatment outlet. Pure water equipment
1. R / O terminal water output of primary reverse osmosis system:
2.5 tons/hour. 2. Outlet conductivity of reverse osmosis system:
less than 20us / cm. 3. Raw water quality: The buyer provides a
water quality report. 4. System recovery rate: about 70%. 5.
Process flow: Raw water → raw water pump → multi-media filter →
activated carbon filter → precision filter → high-pressure pump →
reverse osmosis R / O device → Terminal water tank → Terminal water
pump → Process water GEMA Manual Spray Gun Wear-resistant unit for
coating of difficult geometries State-of-the art design and high
performance materials guarantee excellent powder distribution and
best coating results for application of abrasive enamel powder.
OptiGun® Automatic Gun: efficient and reliable OptiGuns offer the
highest transfer efficiency, perfect quality in every application
and are the ideal solution for color change. Detailed Images Gun
nozzle design Powder coating requires a perfect combination of
nozzle design and high voltage supply to achieve an homogeneous
powder cloud. • The high voltage field plays a very important role
ensuring a perfect powder ato
Related products about Fully Automatic Lift / Elevator Board Painting Powder Coating Line, High Quality Ce Approved Spray Paint Booth for Electric Lift Board
-
Waste Tyre Plastic Recycling Machinery Machine Tire Crusher Production Line Rubber Crumb Grinding Machine Equipment Tire Shredder
-
Stretch Plastic Blowing Pet Bottle Making Blow Molding Machine Bottles Stretch Automatic Pet Bottle Blowing Machine
-
Waste Plastic Pet Bottle, Water Bottle Flake, PP/HDPE/LDPE PE Film Jumbo Woven Bags Plastic Crusher Machine, Plastic Crushing Washing Recycling Machine
-
Type 2 Wall-Mounted Electric Car Charging Station 7kw /11 Kwelectric Vehicle Charging Station Home Wallbox AC EV Charger Single Phase or 3three Phase
-
G-View G12W Wholesale Auto Car LED Headlight Bulb High Power H13 H11 9005 H7 H4 Car LED Headlights LED Car Lights
-
New Design Porcelain Round Plates Dinner Set for Wedding and Banquet
-
China 2023 New Design Super Soft 100% Polyester Microfiber Knitted Oversized Decoration Hoodie Blanket
-
Handmade Art Creative Materials Thickened White Paper Cup DIY Disposable Handmade Colored Paper Cup